XT09-PKI-E-NA Digi International/Maxstream, XT09-PKI-E-NA Datasheet - Page 28

no-image

XT09-PKI-E-NA

Manufacturer Part Number
XT09-PKI-E-NA
Description
MODEM RF 900MHZ 1W ETHER INT
Manufacturer
Digi International/Maxstream
Series
XTend™r
Datasheet

Specifications of XT09-PKI-E-NA

Function
Transceiver, Modem
Modulation Or Protocol
FHSS, FSK
Frequency
900MHz
Interface
RJ-45 Ethernet
Sensitivity
-110dBm
Data Rate - Maximum
10 kbps
Voltage - Supply
7 V ~ 28 V
Package / Case
Module
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Features
-
Power - Output
-
Applications
-
9XTend‐PKG‐E™ Ethernet RF Modem – Product Manual v2.x4x [2007.01.04]
DT (Destination Address) Command
E0 (Echo Off) Command
E1 (Echo On) Command
ER (Receive Error Count) Command
FH (Force Wake-up Initializer) Command
<Networking & Security> DT Command is used to
set/read the networking address of an RF
modem. The modems utilize three filtration lay-
ers: Vendor ID Number (ATID), Channel (ATHP),
and Destination Address (ATDT). The DT com-
mand assigns an address to a modem that
enables it to communicate only with other
modems having the same address. All modems
that share the same DT parameter can communi-
cate with each other.
RF modems in the same network with a different destination address (than that of the transmitter)
will listen to all transmissions to stay synchronized, but will not send any of the data out their
serial ports.
<Command Mode Options> E0 Command turns
off character echo in AT Command Mode.
By default, echo is off.
<Command Mode Options> E1 Command enables
character echo in AT Command Mode. Each typed
character will be echoed back to the terminal
when ATE1 is active. E0 (Echo Off) is the default.
<Diagnostics> The ER command is used to set/
read the number of receive-errors. The error
count records the number of packets partially
received then aborted on a reception error. This
value returns to 0 after a reset and is not non-
volatile (Value does not persist in the modem's
memory after a power-up sequence). Once the
Receive Error Count reaches its maximum value
(up to 0xFFFF), it remains at its maximum count
value until the maximum count value is explicitly changed or the modem is reset.
The ER parameter is not reset by pin, serial port or cyclic sleep modes.
<Sleep (Low Power)> The FH command is used
to force a Wake-up Initializer to be sent on the
next transmission. Use only with cyclic sleep
modes active on remote modems.
ATFH will not send a long header if ATHT = 0xFFFF. WR (Write) Command does not need to be
issued with FH Command.
© 2007 MaxStream, Inc., Confidential & Proprietary ‐ All Rights Reserved 
AT Command: ATDT
Binary Command: 0x00
Parameter Range: 0 - 0xFFFF
Default Parameter Value: 0
Number of bytes returned: 2
Related Commands: HP (Hopping Channel), ID
(Modem VID), MK (Address Mask), MY (Source
Address)
AT Command: ATE0
Binary Command: 0x0A (10 decimal)
AT Command: ATE1
Binary Command: 0x0B (11 decimal)
AT Command: ATER
Binary Command: 0x0F (15 decimal)
Parameter Range: 0 - 0xFFFF
Default Parameter Value: 0
Number of bytes returned: 2
Related Commands: GD (Receive Good Count)
AT Command: ATFH
Binary Command: 0x0D (13 decimal)
     28

Related parts for XT09-PKI-E-NA