XT09-PKI-EA-NA Digi International/Maxstream, XT09-PKI-EA-NA Datasheet - Page 56

• Manufacturer Part Number: XT09-PKI-EA-NA
• Description: MODEM RF 900MHZ 1W ETHER INT
• Manufacturer: Digi International/Maxstream
• Series: XTend™r

Specifications of XT09-PKI-EA-NA

• Function: Transceiver, Modem
• Modulation Or Protocol: FHSS, FSK
• Frequency: 900MHz
• Interface: RJ-45 Ethernet
• Sensitivity: -110dBm
• Data Rate - Maximum: 10 kbps
• Voltage - Supply: 7 V ~ 28 V
• Package / Case: Module
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Power - Output: -
• Applications: -

9XTend‐PKG‐E™ Ethernet RF Modem – Product Manual v2.x4x [2007.01.04]
Appendix A: Agency Certifications
FCC (United States) Certification
Labeling Requirements
FCC Notices
The XTend Ethernet RF Modem complies with Part 15 of the FCC rules and regulations. Compliance
with the labeling requirements, FCC notices and antenna usage guidelines is required.
In order to operate under MaxStream’s FCC Certification, OEMs/integrators must comply with the
following regulations:
Figure A‐01. Required FCC Label for OEM products containing the XTend Ethernet RF Modem
IMPORTANT: The XTend Ethernet RF Modem has been certified by the FCC for use with other
products without any further certification (as per FCC section 2.1091). Modifications not expressly
approved by MaxStream could void the user's authority to operate the equipment.
IMPORTANT: OEMs must test final product to comply with unintentional radiators (FCC section
15.107 & 15.109) before declaring compliance of their final product to Part 15 of the FCC Rules.
IMPORTANT: The RF modem has been certified for remote and base radio applications. If the
modem will be used for portable applications, the device must undergo SAR testing.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the inter-
ference by one or more of the following measures: Re-orient or relocate the receiving antenna,
Increase the separation between the equipment and receiver, Connect equipment and receiver to
outlets on different circuits, or Consult the dealer or an experienced radio/TV technician for help.
Contains FCC ID: OUR-9XTEND
The enclosed device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (i.) this device may not cause harmful interference and (ii.) this device must accept any inter-
ference received, including interference that may cause undesired operation.
1.
2.
© 2007 MaxStream, Inc., Confidential & Proprietary ‐ All Rights Reserved
The OEM/integrator must ensure that the text provided with this device [Figure A-01] is
placed on the outside of the final product and within the final product operation manual.
The XTend Ethernet RF Modem may only be used with antennas that have been tested and
approved for use with this modem [refer to ‘FCC-approved Antennas’ section].
WARNING: The Original Equipment Manufacturer (OEM) must ensure that FCC labeling
requirements are met. This includes a clearly visible label on the outside of the final
product enclosure that displays the text shown in the figure below.
56