ATMEGA128RFA1-ZUR Atmel, ATMEGA128RFA1-ZUR Datasheet - Page 275

• Manufacturer Part Number: ATMEGA128RFA1-ZUR
• Description: IC AVR MCU 2.4GHZ XCEIVER 64QFN
• Manufacturer: Atmel
• Series: ATMEGAr

Specifications of ATMEGA128RFA1-ZUR

• Frequency: 2.4GHz
• Data Rate - Maximum: 2Mbps
• Modulation Or Protocol: 802.15.4 Zigbee
• Applications: General Purpose
• Power - Output: 3.5dBm
• Sensitivity: -100dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Current - Receiving: 12.5mA
• Current - Transmitting: 14.5mA
• Data Interface: PCB, Surface Mount
• Memory Size: 128kB Flash, 4kB EEPROM, 16kB RAM
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-VFQFN, Exposed Pad
• Processor Series: ATMEGA128x
• Core: AVR8
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 128 KB
• Data Ram Size: 16 KB
• Interface Type: JTAG
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 38
• Number Of Timers: 6
• Operating Supply Voltage: 1.8 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVR128RFA1-EK1
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Boot Loader Lock
Bits
2467V–AVR–02/11
Figure 133. Memory Sections
Note:
If no Boot Loader capability is needed, the entire Flash is available for application code. The
Boot Loader has two separate sets of Boot Lock bits which can be set independently. This gives
the user a unique flexibility to select different levels of protection.
The user can select:
•
•
•
•
See
Serial or Parallel Programming mode, but they can be cleared by a chip erase command only.
The general Write Lock (Lock bit mode 2) does not control the programming of the Flash mem-
ory by SPM instruction. Similarly, the general Read/Write Lock (Lock bit mode 3) does not
control reading nor writing by LPM/SPM, if it is attempted.
To protect the entire Flash from a software update by the MCU
To protect only the Boot Loader Flash section from a software update by the MCU
To protect only the Application Flash section from a software update by the MCU
Allow software update in the entire Flash
Table 108
1. The parameters in the figure above are given in
Boot Loader Flash Section
Boot Loader Flash Section
Application Flash Section
Application Flash Section
Application Flash Section
Application Flash Section
Program Memory
Program Memory
BOOTSZ = '11'
BOOTSZ = '01'
and
Table 109
$0000
End RWW
Start NRWW
End Application
Start Boot Loader
Flashend
$0000
End RWW
Start NRWW
End Application
Start Boot Loader
Flashend
for further details. The Boot Lock bits can be set in software and in
(1)
Boot Loader Flash Section
Boot Loader Flash Section
Application Flash Section
Application Flash Section
Application flash Section
Program Memory
Program Memory
BOOTSZ = '10'
BOOTSZ = '00'
Table on page
284.
$0000
End RWW
Start NRWW
End Application
Start Boot Loader
Flashend
$0000
End RWW, End Application
Start NRWW, Start Boot Loader
Flashend
ATmega128
275