ATA8742-PXQW Atmel, ATA8742-PXQW Datasheet - Page 45

• Manufacturer Part Number: ATA8742-PXQW
• Description: MCU W/TRANSMITTER ASK/FSK 24QFN
• Manufacturer: Atmel

Specifications of ATA8742-PXQW

• Frequency: 433MHz
• Applications: Home Automation, Remote Sensing, RKE
• Modulation Or Protocol: ASK, FSK
• Data Rate - Maximum: 32 kBit/s
• Power - Output: 7.5dBm
• Current - Transmitting: 9.8mA
• Data Interface: PCB, Surface Mount
• Antenna Connector: PCB, Surface Mount
• Memory Size: 4kB Flash, 256B EEPROM, 256B SRAM
• Voltage - Supply: 2 V ~ 4 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 24-VQFN Exposed Pad, 24-HVQFN, 24-SQFN, 24-DHVQFN
• Processor Series: ATA8x
• Core: AVR8
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 4 KB
• Data Ram Size: 256 B
• Interface Type: SPI, USI
• Maximum Clock Frequency: 8.1 MHz
• Number Of Programmable I/os: 12
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ATASTK512-EK1-IND
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Lead Free Status / Rohs Status: Details

14.6
14.7
9151A–INDCO–07/09
Calibrated Internal RC Oscillator
External Clock
By default, the Internal RC Oscillator provides an approximate 8 MHz clock. Though voltage and
temperature dependent, this clock can be very accurately calibrated by the user. See
on page 197
with the CKDIV8 Fuse programmed. See
This clock may be selected as the system clock by programming the CKSEL Fuses as shown in
Table
the pre-programmed calibration value into the OSCCAL Register and thereby automatically cali-
brates the RC Oscillator. The accuracy of this calibration is shown as Factory calibration in
29-2 on page
By changing the OSCCAL register from SW, see
page
The accuracy of this calibration is shown as User calibration in
When this Oscillator is used as the chip clock, the Watchdog Oscillator will still be used for the
Watchdog Timer and for the Reset Time-out. For more information on the pre-programmed cali-
bration value, see the section
Table 14-6.
Note:
When this Oscillator is selected, start-up times are determined by the SUT Fuses as shown in
Table 14-7 on page
Table 14-7.
Note:
To drive the device from an external clock source, CLKI should be driven as shown in
14-3 on page
grammed to “0000”.
SUT1..0
10
00
01
11
48, it is possible to get a higher calibration accuracy than by using the factory calibration.
(1)
14-6. If selected, it will operate with no external components. During reset, hardware loads
1. The device is shipped with this option selected.
1. The device is shipped with this option selected.
and
CKSEL3..0
197.
Internal Calibrated RC Oscillator Operating Modes
Start-up Times for the Internal Calibrated RC Oscillator Clock Selection
46. To run the device on an external clock, the CKSEL Fuses must be pro-
0010
“Internal Oscillator Speed” on page 221
from Power-down
(1)
45..
Start-up Time
6 CK
6 CK
6 CK
“Calibration Byte” on page
“System Clock Prescaler” on page 47
Additional Delay from
Reset (V
Reserved
“Oscillator Calibration Register – OSCCAL” on
14CK + 64 ms
14CK + 4 ms
14CK
CC
182.
Nominal Frequency
for more details. The device is shipped
= 5.0V)
8.0 MHz
Table 29-2 on page
Recommended Usage
BOD enabled
Fast rising power
Slowly rising power
ATA8742
for more details.
197.
Table 29-2
Figure
Table
45