V-16G-3C26 Omron, V-16G-3C26 Datasheet

SWTCH MINI SPST-NO 16A PIN PLNGR

V-16G-3C26

Manufacturer Part Number
V-16G-3C26
Description
SWTCH MINI SPST-NO 16A PIN PLNGR
Manufacturer
Omron
Series
Vr
Type
Miniature Basic Switchr
Datasheets

Specifications of V-16G-3C26

Circuit
SPST-NO
Switch Function
Off-Mom
Contact Rating @ Voltage
16A @ 250VAC
Actuator Type
Round (Pin Plunger)
Mounting Type
Chassis Mount
Termination Style
Quick Connect - .187" (4.7mm)
Operating Force
400gf
Contact Form
SPDT
Contact Rating
16 Amps at 250 Volts
Actuator
Plunger, Pin
Microswitch Type
Miniature
Actuator Style
Pin Plunger
Operating Force Max
400gf
Contact Voltage Ac Nom
250V
Contact Voltage Dc Nom
250V
Contact Current Max
16A
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
SW1072
V-16G-3C26
V16G3C26
General Purpose Snap Action Switch
• Industry standard design with switching currents of 10A to 21A
• Widely used for applications where long life expectancy and
• Choose from a variety of levers, terminals and operating forces.
• Right and Left Barrier options are available for the V-21 and
• Heat resistant versions of the V-15 and V-10 are available.
• RoHS Compliant
Ordering Information
■ Model Number Legend
1.
2.
3.
V -
high reliability is required.
V-16 models
Snap Action Switch
V
Ratings
21:
16:
15:
11:
10:
Contact Gap
None: 1 mm (F gap)
G:
Actuator
None: Pin plunger
1:
2:
3:
4:
5:
6:
1
2
21 A at 250 VAC
16 A at 250 VAC
15 A at 250 VAC
11 A at 250 VAC
10 A at 250 VAC
0.5 mm (G gap)
Short hinge lever
Hinge lever
Long hinge lever
Simulated roller lever
Short hinge roller lever
Hinge roller lever
3
-
4 5
6
7
Note: Consult Omron regarding nominclature combinations and part numbers
-
8
-
not found in this datasheet.
9
4.
5.
6. Insulation Barrier
COM Terminal, Bottom position:
COM Terminal, Side position:
(Barriers available for V-21 and V-16, only)
3:
4:
5:
6:
Contact Form
1:
2:
Terminals
A:
C2:
C:
None: Without Barrier
R:
L:
SPST-NC
SPST-NO
SPDT
SPST-NC
SPST-NO
Right-hand barrier
Left-hand barrier
SPDT
Solder terminals
Quick-connect terminal (#187)
Quick-connect terminal (#250)
Snap Action Switch
7.
8.
9.
5:
4:
K:
Maximum Operating Force
6:
Note: These OF values are for
Special Purpose
None: Standard
T:
Mounting Hole Size
None: 3.1 mm
the pin plunger models.
400 gf
200 gf
100 gf
2.9 mm
Heat resistive
(V-15 and V-10, only)
V
121

Related parts for V-16G-3C26

V-16G-3C26 Summary of contents

Page 1

... Widely used for applications where long life expectancy and high reliability is required. • Choose from a variety of levers, terminals and operating forces. • Right and Left Barrier options are available for the V-21 and V-16 models • Heat resistant versions of the V-15 and V-10 are available. ...

Page 2

... Note: 1. Add “G” to the part number in the appropriate location to obtain a 0.5 mm contact gap. Add “-K” to the part number in the appropriate location to obtain 2.9 mm mounting holes. Example: V-21G2-1C6-K 2. Not all combinations are available. Consult Omron regarding nomenclature combinations and part numbers not found in this datasheet. V ...

Page 3

... Note: 1. Add “G” to the part number in the appropriate location to obtain a 0.5 mm contact gap. Add “-K” to the part number in the appropriate location to obtain 2.9 mm mounting holes. Examples: 1) V-16G3-1C25-K 2) V-11G-1A4-K 2. Not all combinations are available. Consult Omron regarding nomenclature combinations and part numbers not found in this datasheet. Without barrier ...

Page 4

... Note: 1. Add “G” to the part number in the appropriate location to obtain a 0.5 mm contact gap. Add “-K” to the part number in the appropriate location to obtain 2.9 mm mounting holes. Add “C2” to the part number in the appropriate location to obtain versions with #187 quick- connect terminals ...

Page 5

... VDC 250 VDC Note: 1. The above current values are the normal current values of models with a contact gap (gap F), which vary with the normal current values of models with a contact gap of 0.5 mm (gap G). 2. Inductive load has a power factor of 0.4 min. (AC) and a time constant max. (DC). ...

Page 6

... The dielectric strength shown is measured using a separator between the switch and metal mounting plate. 3. For pin plunger models, the above values apply for use at both the free position and total travel position. For lever models, they apply at the total travel position. ...

Page 7

... Bottom type Side type * The SPST-NC and SPST-NO contact form types listed in the ordering information tables are for Pin Plunger models only. For information concerning lever models consult Omron. ■ Electrical service life (Pin plunger models) V-21/-16/-15 5 Operating frequency: 60 operations/min cosφ ...

Page 8

... Terminals Note: 1. Unless otherwise specified, all units are in millimeters and a tolerance of ±0.4 mm applies to all dimensions 2. The following table is for the SPDT contact specifications. Two terminals will be available for SPST-NO or SPST-NC contact specifications. For terminal positions, refer to the above Contact Form 3 ...

Page 9

... The @ in the model number is for the terminal code. 4. The illustrations for V-21, V-16 and V-11 show a hole size of 3.1 mm. V-21, V-16 and V-11 models with a suffix “K” have a hole size of 2.9 mm. 5. The operating characteristics are for operation in the A direction ( Pin Plunger Models 20.2± ...

Page 10

... The @ in the model number is for the terminal code. 4. The illustrations for V-21, V-16 and V-11 show a hole size of 3.1 mm. V-21, V-16 and V-11 models with a suffix “K” have a hole size of 2.9 mm. 5. The operating characteristics are for operation in the A direction ( ...

Page 11

... The @ in the model number is for the terminal code. 4. The illustrations for V-21, V-16 and V-11 show a hole size of 3.1 mm. V-21, V-16 and V-11 models with a suffix “K” have a hole size of 2.9 mm. 5. The operating characteristics are for operation in the A direction ( ...

Page 12

... The following illustrations are for quick-connect terminals (#250) (terminals C). Refer to Terminals section for the dimensions of other terminals. 3. The @ in the model number is for the terminal code. 4. The illustrations show models with a suffix “K”, which have a hole size of 2.9 mm. Omit the “K” to obtain models with hole size = 3.1 mm. 5. The operating characteristics are for operation in the A direction ( Pin Plunger Models 20.2± ...

Page 13

... The following illustrations are for quick-connect terminals (#250) (terminals C). Refer to Terminals section for the dimensions of other terminals. 3. The @ in the model number is for the terminal code. 4. The illustrations show models with a suffix “K”, which have a hole size of 2.9 mm. Omit the “K” to obtain models with hole size = 3.1 mm. 5. The operating characteristics are for operation in the A direction ( Simulated Roller Lever Models 3 ...

Page 14

... According to EN61058-1, the minimum insulation thickness for this switch should be 1.1 mm and minimum clearance distance between the terminal and mounting plate should be 1.0 mm. If the insulation distance cannot be provided in the product incorporating the switch, either use a switch with insulation barrier or use a separator to ensure sufficient insulation distance. ...

Page 15

... MEMO V Snap Action Switch ...

Page 16

... All sales are subject to Omron Electronic Components LLC standard terms and conditions of sale, which can be found at http://www.components.omron.com/components/web/webfiles.nsf/sales_terms.html ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527. OMRON ELECTRONIC COMPONENTS LLC 55 E. Commerce Drive, Suite B ...

Related keywords