B19JH/M4G NKK Switches, B19JH/M4G Datasheet

SWITCH TOGGLE SPDT BAT R/A 94VO

B19JH/M4G

Manufacturer Part Number
B19JH/M4G
Description
SWITCH TOGGLE SPDT BAT R/A 94VO
Manufacturer
NKK Switches
Series
Br
Datasheet

Specifications of B19JH/M4G

Circuit
SPDT
Switch Function
On-Off-Mom
Contact Rating @ Voltage
0.4VA @ 28VAC/DC
Actuator Type
Standard Round
Actuator Length
6.30mm
Illumination
Non-Illuminated
Mounting Type
Through Hole
Termination Style
PC Pin
Bushing Thread
Unthreaded
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
B19JH/M4G-RO
B19JH/M4G-RO
A
General
Series B
Electrical Capacity (Resistive Load)
Other Ratings
Materials & Finishes
Environmental Data
Installation
PCB Processing
Standards & Certifications
A12
Operating Temperature Range:
Nominal Operating Force:
Flammability Standards:
Insulation Resistance:
Stationary Contacts:
Contact Resistance:
Dielectric Strength:
Movable Contact:
Mounting Torque:
Support Bracket:
Mechanical Life:
Angle of Throw:
Contact Timing:
Case Housing:
Electrical Life:
Logic Level:
Soldering:
Terminals:
Vibration:
Humidity:
Cleaning:
Bushing:
Gasket:
Toggle:
Shock:
Specifications
0.4VA maximum @ 28V AC/DC maximum
(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Note: Find additional explanation of operating range in Supplement section.
50 milliohms maximum
500 megohms minimum @ 500V DC
500V AC minimum for 1 minute minimum
100,000 operations minimum for On-None-On & On-Off-On
50,000 operations minimum for other circuits
50,000 operations minimum for locking lever models
50,000 operations minimum
Toggles A, A1, E & K with Long Paddle: 1.47N (momentary); 1.18N (maintained)
Toggles J & H & K with Short Paddle: 2.72N (momentary); 1.84N (maintained)
Toggle L: 0.59N
Nonshorting (break-before-make)
26°
Nickel plated brass
Carbon blended polyamide; nickel plated zinc alloy for locking levers & threaded bushing
Nitrile butadiene rubber
Glass fiber reinforced polyamide
Tin plated phosphor bronze
Phosphor bronze with gold plating
Copper alloy with gold plating
Copper alloy with gold plating
–30°C through +85°C (–22°F through +185°F)
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
50G (490m/s
.30 ~ .45Nm (2.65 ~ 3.98 lb
Wave Soldering Recommended: See Profile A in Supplement section.
Manual Soldering: See Profile A in Supplement section.
Automated cleaning. See Cleaning specifications in Supplement section.
UL94V-0 available
The B Series toggles have not been tested for UL recognition or CSA certification.
These switches are designed for use in a low-voltage, low-current, logic-level circuit.
When used as intended in a logic-level circuit, the results do not produce hazardous energy.
2
) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
www.nkk.com
Process Sealed Subminiature Antistatic Toggles
in) for A1 actuator with threaded bushing only

Related parts for B19JH/M4G

B19JH/M4G Summary of contents

Page 1

... Standards & Certifications Flammability Standards: UL94V-0 available The B Series toggles have not been tested for UL recognition or CSA certification. These switches are designed for use in a low-voltage, low-current, logic-level circuit. When used as intended in a logic-level circuit, the results do not produce hazardous energy. ...

Page 2

... Static electricity from an operator’s touch travels from actuator through the bushing and bracket to the PC board. Locking lever mechanism offered as a toggle option. Optional threaded, 6mm diameter bushing for panel seal mounting meets IP65 of IEC60529 specifications (similar to NEMA 4 and 13). ...

Page 3

... OFF (ON OFF (ON (ON) OFF Momentary * Reverse circuits R & S available with right angle & vertical only Straight PC Terminals A14 Process Sealed Subminiature Antistatic Toggles TYPICAL SWITCH ORDERING EXAMPLE Toggles Terminals P Straight * B Straight with Bracket * H Right Angle with Bracket * V Vertical with Bracket * Bracketed models are ESD protected ...

Page 4

... Process Sealed Subminiature Antistatic Toggles Toggle Position ( ) = Momentary Up Center Pole Model Slot B12 ON NONE B13 ON OFF B15 ON NONE SP B1R (ON) NONE B18 (ON) OFF B19 ON OFF B1S (ON) OFF B22 ON NONE B23 ON OFF B25 ON NONE DP B2R (ON) NONE B28 (ON) OFF B29 ON OFF B2S (ON) OFF .394” (10.0mm) ...

Page 5

... AT4003 G .394” (10.0mm) Bat Lever Cap Material: PVC (11.0) .433 Colors Available Black White A16 Process Sealed Subminiature Antistatic Toggles PC TERMINALS B Straight with Bracket (3.1) Typ .122 V Vertical with Bracket (2.54) Typ .100 (0.6) Dia Typ .024 OPTIONAL CAPS AT4064 J .248” ...

Page 6

... Process Sealed Subminiature Antistatic Toggles (6.0) Dia (2.6) Dia .236 .102 26° Slot (3.5) .138 (6.8) (10.0) .268 .394 (2.6) Dia (6.0) Dia .102 .236 26° Slot (3.5) .138 (10.0) (8.8) .394 .346 (6.0) Dia (2.6) Dia .236 .102 26° Slot (6 ...

Page 7

... Slot (8.0) .315 B12LB Locking Lever • Straight PC • Bracket (6.0) Dia .236 Slot (5.68) .224 (8.85) .348 B22LB A18 Process Sealed Subminiature Antistatic Toggles TYPICAL SWITCH DIMENSIONS Double Pole (2.6) Dia .102 Slot (0.4) .016 (2.7) (5.08) .106 .200 (8.8) (10.0) (16 ...

Page 8

... Process Sealed Subminiature Antistatic Toggles (2.6) Dia M6 P0.75 .102 26° Slot (4.8) .189 (8.0) (6.8) .315 .268 (2.6) Dia M6 P0.75 .102 26° Slot (4.8) .189 (8.0) (8.8) .346 .315 STANDARD HARDWARE & PANEL CUTOUT AT513M Metric Hex Nut M6 P0.75 (8.0) .315 ...

Related keywords