LAN7500-ABZJ SMSC, LAN7500-ABZJ Datasheet - Page 38

• Manufacturer Part Number: LAN7500-ABZJ
• Description: IC USB-10/100/1K ETH CTRL 56QFN
• Manufacturer: SMSC

Specifications of LAN7500-ABZJ

• Mfg Application Notes: LAN7500 Schematic
• Design Resources: LAN7500 BOM
• Controller Type: Ethernet Controller, USB 2.0 to 10/100/1K
• Interface: USB/Serial
• Voltage - Supply: 1.2V, 2.5V, 3.3V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 56-VFQFN Exposed Pad
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Supply: -
• Other names: 638-1108

Chapter 7 Operational Characteristics
Revision 1.0 (11-01-10)
7.1
Absolute Maximum Ratings*
Supply Voltage (VDDVARIO)
Analog Supply Voltage (VDD12A)
Analog USB Supply Voltage (VDD33A)
Digital Core Supply Voltage (VDD12CORE)
Ethernet Magnetics Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to +3.6V
Positive voltage on signal pins, with respect to ground
Negative voltage on signal pins, with respect to ground
Positive voltage on XI, with respect to ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +4.6V
Positive voltage on XO, with respect to ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +2.5V
Ambient Operating Temperature in Still Air (T
Junction to Ambient (θ
Junction to Top of Package (Ψ
Storage Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-55
Lead Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Refer to JEDEC Spec. J-STD-020
HBM ESD Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .JEDEC Class 3A
Latch-up Performance per EIA/JESD 78 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+/-150mA
Note 7.1
Note 7.2
Note 7.3
Note 7.4
*Stresses exceeding those listed in this section could cause permanent damage to the device. This is
a stress rating only. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability. Functional operation of the device at any condition exceeding those indicated in
Section 7.2, "Operating
of this specification is not implied. Note, device signals are NOT 5 volt tolerant unless specified
otherwise.
When powering this device from laboratory or system power supplies, it is important that
the absolute maximum ratings not be exceeded or device failure can result. Some power
supplies exhibit voltage spikes on their outputs when AC power is switched on or off. In
addition, voltage transients on the AC power line may appear on the DC output. If this
possibility exists, it is suggested that a clamp circuit be used.
This rating does not apply to the following pins: XI, XO, ETHRBIAS, USBRBIAS.
This rating does not apply to the following pins: ETHRBIAS, USBRBIAS.
0
o
C to +70
JA
o
Conditions**",
C for commercial version, -40
) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24.4
(Note
JT
) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.1
(Note
DATASHEET
7.1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to +3.6V
Section 7.4, "DC
(Note
7.1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to +1.5V
38
(Note
A
7.1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to +3.6V
). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.1) . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to +1.5V
o
Hi-Speed USB 2.0 to 10/100/1000 Ethernet Controller
C to +85
(Note
Specifications", or any other applicable section
(Note
7.2) . . . . . . . . . . . . . . . . . . . . . . . . +6.0V
7.3) . . . . . . . . . . . . . . . . . . . . . . . . -0.5V
o
C for industrial version.
SMSC LAN7500/LAN7500i
o
C to +150
Datasheet
Note 7.4
o
o
C/W
C/W
o
C