NMTC-S20200XRGHS-10 Microtips Technology, NMTC-S20200XRGHS-10 Datasheet
NMTC-S20200XRGHS-10
Specifications of NMTC-S20200XRGHS-10
Related parts for NMTC-S20200XRGHS-10
NMTC-S20200XRGHS-10 Summary of contents
Page 1
... Microtips 12F, No 31, Lane 169, Kang Ning St. Technology Hsi-Chih, Taipei Hsien, Taiwan, R.O.C. LCD MODULE SPECIFICATION FOR CUSTOMER’S APPROVAL CUSTOMER : NMTC-S20200XRGHS MODULE TYPE : APPROVED BY: (FOR CUSTOMER USE ONLY) Approved By Checked By Prepared By MT File No 微 端 91.04 .26 91.04 .26 廖 宗 錦 ...
Page 2
ITEM FEATURES LCD MODULE DRAWING GENERAL SPECIFICATION ABSOLUTE MAXIMUN RATING ELECTRICAL CHARACTERISTICS OPTICAL CHARACTERISTICS MECHANICAL SPECIFICATION INTERFACE PIN ASSIGNMENT BLOCK DIAGRAM POWER SUPPLY DIAGRAM TIMING CHARACTERISTICS READ/WRITE TIMING CHART COMMANDS COMMANDS DESCRIPTION DD RAM ADDRESSING CG RAM MAPPING CHARACTER FONT ...
Page 3
... Temperature Range CCFL Inverter EL Driver IC Touch Screen TO BE VERY CAREFUL ! The LCD driver ICs are made of CMOS process, which is very easy to be damaged by static charge, make sure the user is grounded when handling the LCM. FEATURES of NMTC-S20200XRGHS ) O’clock FSTN Positive STN Gray ...
Page 4
4 ...
Page 5
GENERAL SPECIFICATION Item Display Resolution Dimensional Outline(mm) Display mode Circuit Interface ABSOLUTE MAXIMUN RATING (1) Electrical Absolute Ratings Item Power Supply for Logic Power Supply for LCD Input Voltage Supply Current for LED backlight Note: Operator should be grounded during ...
Page 6
ELECTRICAL CHARACTERISTICS Item Symbol Power Supply for Logic V IL Input Voltage V IH LCM V =5.0V DD Recommend V -Vo= DD LCD Module 4.0V Driving Voltage I DD Power Supply (B/L OFF) Current for LCM ...
Page 7
... Dot Pitch Duty Ratio Character Font Table LCD Display Mode Rear Polarizer: Viewing Direction Backlight Controller DC/DC Converter CCFL Inverter EL Driver NMTC-S20200XRGHS 116.0(W)mm×37.0(H)mm×10.0(D)mm Max 20 characters×2 lines 3.2 mm×5.55 mm 3.7 mm×5.95 mm 0.60(W)mm×0.65(H)mm 0.65(W)mm×0.70(H)mm 1/16 Duty English European STN Gray Mode Black & ...
Page 8
INTERFACE PIN ASSIGNMENT PIN NO. PIN OUT 1 V Ground Logic Circuit Power Supply Power Supply For LCD Panel, please refer to page 11 for connection Data/ Instruction Register Select 5 R/W ...
Page 9
Definition of Operation Voltage (Vop) Selected Wave Intensity 100％ Cr Max Vop [positive type] [Note 8] Definition of Response Time (Tr, Tf) Non-selected Selected Conition Conition Intensity 90％ 100％ Tr [positive type] Conditions: Operating Voltage : Vop Frame ...
Page 10
Definition of viewing angle [Note 11] Description of Measuring Equipment 10 ...
Page 11
BLOCK DIAGRAM POWER SUPPLY 11 ...
Page 12
TIMING CHARACTERISTICS AC Characteristics ( Mode Characteristic E Cycle Time E Rise/Fall Time E Pulse Width(High, Low) R/W And RS Setup Time R/W And RS Hold Time Data Setup Time Data Hold Time E Cycle Time ...
Page 13
Read/Write Timing Chart 13 ...
Page 14
Commands Instruction RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Clear Display Return Home Entry Mode Display ON/OFF Cursor or Display Shift Function ...
Page 15
COMMANDS DESCRIPTION Clear Display RS R/W DB7 DB6 Clear all the display data by writing "20H" (space code) to all DDRAM address, and set DDRAM address to "00H" into AC (address counter). Return cursor to the original ...
Page 16
Display ON/OFF Control RS R/W DB7 DB6 Control display/cursor/blink ON/OFF 1 bit register Display ON/OFF control bit When D = "High", entire display is turned on. When D = "Low", display is turned off, but ...
Page 17
Function Set RS R/W DB7 DB6 Interface data length control bit When DL = "High", it means 8-bit bus mode with MPU. When DL = "Low", it means 4-bit bus mode with MPU ...
Page 18
Write Data to RAM RS R/W DB7 DB6 Write binary 8-bit data to DDRAM/CGRAM. The selection of RAM from DDRAM, CGRAM, is set by the previous address set instruction : DDRAM address set, CGRAM address set. ...
Page 19
DD RAM ADDRESSING For 16×1 or 8×1 Display Character RAM Address For 16×2 or 8×2 Display Character RAM Address For 16×4 Display Character ...
Page 20
CG RAM MAPPING Character Code (DD RAM data High Low ...
Page 21
CHARACTER FONT TABLE Upper 4 bits 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 Lower 4 bits CG 0000 RAM (1) CG 0001 RAM (2) CG 0010 RAM (3) CG 0011 RAM ...
Page 22
RELIABILITY TEST No Item 1 High Temp. Operation 2 High Temp. Storage 3 Low Temp. Operation 4 Low Temp. Storage 5 High Temp./Humid Storage 6 Thermal Shock Vibration Test 7 ( IEC-68-2-6 ) Shock 8 ( IEC 68-2-27) APPEARANCE CHECK ...
Page 23
HANDLING PRECAUTIONS (1) Treat polarizer very carefully since it is easy to be damaged. (2) When cleaning the display surface, use soft cloth (e.g. gauss) with a solvent (recommended below) and wipe lightly. ◆ ethyl alcohol ◆ iso-prcolol Do not ...
Page 24
LCD PRODUCT QUALITY STANDARD DISPLAY APPEARANCE No Item inclusions (black spot, 1 white spot, dust) 2 scratch 3 dent 4 bubble 5 pin hole 6 dot defect 7 contrast irregularity(spot) 8 dot width 9 color tone and uniformity obvious uneven ...
Page 25
REVISION HISTORY Revision Content The LCD module is compliant with RoHS Page 25 Date 11/1/2006 ...