AT3535QR410ZS-RV-C1 Kingbright Corp, AT3535QR410ZS-RV-C1 Datasheet
AT3535QR410ZS-RV-C1
Specifications of AT3535QR410ZS-RV-C1
Related parts for AT3535QR410ZS-RV-C1
AT3535QR410ZS-RV-C1 Summary of contents
Page 1
... The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAI9279 REV NO: V.4 APPROVED: WYNEC CHECKED: Allen Liu 3.5X3.5mm SMD LED WITH CERAMIC SUBSTRATE Part Number: AT3535QR410ZS-RV-C1 Material as follows: Package : Ceramics Encapsulating resin : Silicone resin Electrodes : Ag plating COOL WHITE DATE: MAR/26/2009 DRAWN: D ...
Page 2
... Selection Guide Part No. AT3535QR410ZS-RV-C1 Cool White (AlGaInN) Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value. 2. Luminous intensity / luminous flux: +/-15%. Absolute Maximum Ratings at T Parameter DC Forward Current [1] Peak Forward Current [2] Power dissipation Operating Temperature ...
Page 3
... Cool White AT3535QR410ZS-RV-C1 SPEC NO: DSAI9279 REV NO: V.4 APPROVED: WYNEC CHECKED: Allen Liu 3.5X3.5mm SMD LED WITH CERAMIC SUBSTRATE DATE: MAR/26/2009 DRAWN: D.M.Su PAGE ERP: 1212000049 ...
Page 4
SPEC NO: DSAI9279 REV NO: V.4 APPROVED: WYNEC CHECKED: Allen Liu 3.5X3.5mm SMD LED WITH CERAMIC SUBSTRATE DATE: MAR/26/2009 DRAWN: D.M.Su PAGE ERP: 1212000049 ...
Page 5
... AT3535QR410ZS-RV-C1 0.44 0.42 0.40 0.38 6000 K 0.36 7000 K 0.34 27 0.32 28 0.30 0.28 0.30 Group Chromaticity Regions 10, 11 13, 14, 15 17, 18, 19, 20, 21 23, 24, 25, 26, 27 0.4582 0.4099 0.4687 0.4289 1 0.4813 0.4319 0.4700 0.4126 0.4483 0.3919 0.4582 0.4099 2 0.4700 0.4126 0.4593 0.3944 0.4465 0.4071 ...
Page 6
Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm ; Tolerance: ± 0.1) Tape Dimensions (Units : mm) ...
Page 7
... LEDs are transported, we recommend that you use the same packing methods as Kingbright’s. SPEC NO: DSAI9279 REV NO: V.4 APPROVED: WYNEC CHECKED: Allen Liu 3.5X3.5mm SMD LED WITH CERAMIC SUBSTRATE AT3535QR410ZS-RV-C1 DATE: MAR/26/2009 DRAWN: D.M.Su PAGE ERP: 1212000049 ...
Page 8
JEDEC Moisture Sensitivity: Level Floor Life Time Conditions ≤ 30 ° weeks Notes: 1. CAUTION - The ‘‘accelerated equivalent’’ soak requirements shall not be used until correlation of damage response, including electrical, after soak and ...
Page 9
Handling Precautions Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic significantly reduces thermal stress more susceptible to damage by external mechanical force result, special handling precautions need ...
Page 10
Designing the Position of LED on a Board. 1.No twist/warp/bent/or other stress shall be applied to the board after mounting LED with solder to avoid a crack of LED package. Refer to the following recommended position and direction of LED. ...
Page 11
Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below Lot Tolerance Percent Defective (LTPD) : 10% No. Test Item 1 Continuous Operating Test High Temperature Operating 2 Test Low Temperature Operating 3 Test ...