LPC1766-STK Olimex Ltd., LPC1766-STK Datasheet
LPC1766-STK
Specifications of LPC1766-STK
Available stocks
Related parts for LPC1766-STK
LPC1766-STK Summary of contents
Page 1
... LPC1766-STK development board All boards produced by Olimex are ROHS compliant Copyright(c) 2009, OLIMEX Ltd, All rights reserved Users Manual Revision Initial, October 2009 Page 1 ...
Page 2
... INTRODUCTION: LPC1766-STK is development board with LPC1766 Cortex M3 microcon- troller from NXP. This powerful microcontroller supports various serial interfaces such as USB Device/Host/OTG, UART, CAN and other. On the board are avalable audio input and output, digital accelerometer, JTAG, Ethernet, TFT LCD and mini SD/MMC card connector ...
Page 3
... ELECTROSTATIC WARNING: The LPC1766-STK board is shipped in protective anti-static packaging. The board must not be subject to high electrostatic potentials. General practice for working with static sensitive devices should be applied when working with this board. BOARD USE REQUIREMENTS: Cables: The cable you will need depends on the programmer/debugger you use. If you use ARM-JTAG-EW, you will need USB A-B cable ...
Page 4
Split APB bus allows high throughput with few stalls between the CPU and DMA. Serial interfaces: Ethernet MAC with RMII interface and dedicated DMA controller. USB 2.0 full-speed device/Host/OTG controller with dedicated DMA controller and on-chip PHY for device, Host, ...
Page 5
Repetitive interrupt timer provides programmable and repeating timed interrupts. Each peripheral has its own clock divider for further power savings. Standard JTAG test/debug interface for compatibility with existing tools. Serial Wire Debug and Serial Wire Trace Port options. Emulation trace ...
Page 6
BLOCK DIAGRAM: Page 6 ...
Page 7
MEMORY MAP: Page 7 ...
Page 8
SCHEMATIC CLOSE CAN_T SCL2,SDA2 AGND 2 1 47uF/6. 10uF/6. 3V_BAT 6x3.8x2.5(SMD ...
Page 9
... BOARD LAYOUT: POWER SUPPLY CIRCUIT: LPC1766-STK is typically power supplied with 9 VDC. The programmed board power consumption is about 200 mA with all peripherials enabled Page 9 ...
Page 10
... RESET CIRCUIT: LPC1766-STK reset circuit includes jumper RST_E, pin 15 of JTAG connector, pin 10 of TRACE connector and RESET button. CLOCK CIRCUIT: Quartz crystal 12 MHz is connected to LPC1766 pin 22 (XTAL1) and pin 23 (XTAL2). Quartz crystal 32.768 kHz is connected to LPC1766 pin 16 (RTCX1) and pin 18 (RTCX2) ...
Page 11
This jumper, when closed, supplies analog 5V voltage supply to the audio amplifiers. Default state is closed. AGND_E This jumper, when closed, connects analog GND to the GND of the MCU. Default state is closed. EXT_TEMP/TH1 This jumper, when ...
Page 12
... Joystick button with name J1 this is 4 directions plus center button, in the schematic the joystick four directions switches are connected through 33k resistors to LPC1766 pins - 65 (P2[8]/TD2/TXD2) – RIGHT, 66 (P2[7]/RD2/RTS1) – LEFT, 74 (P2[1]/PWM1[2]/RXD1) – DOWN, 75 (P2[0]/PWM1[1]/TXD1) – UP, the center button is connected to pin 80 (P0[5]/I2SRX_WS/TD2/CAP2[1]) ...
Page 13
EXTERNAL CONNECTORS DESCRIPTION: RS232_0: Pin # RS232_1: Pin # Signal Name NC T2OUT R2IN RST_E GND NC ISP_E NC NC Signal Name ...
Page 14
... Group) port directly to the core. Instructions may be inserted and executed by the core thus allowing LPC1766 memory to be programmed with code and executed step by step by the host software. For more details refer to IEEE Standard 1149.1 - 1990 Standard Test Access Port and Boundary Scan Architecture and LPC1766 datasheets and users manual ...
Page 15
Pin # 1 3.3V 3 TRSTN 5 TDI 7 TMS 9 TCK 11 RTCK 13 TDO 15 RSTN 17 through 10K to GND 19 +5V_JLINK LAN: Signal Name Pin # ...
Page 16
Pin # Signal Name Chip Side 1 TPOUT+ 2 TPOUT Not Connected (NC) LED Right Yellow Left Green CAN Pin# Signal 1 GND 2 CANL 3 CANH TRACE Pin# Signal Description 1 VCC 3,3V 3 GND 5 GND ...
Page 17
Page 17 ...
Page 18
USB_HOST Pin # Signal Name 1 HOST_PWR 2 USB_HOST_D- 3 USB_HOST_D+ 4 GND USB 2.0 full-speed Host controller with dedicated DMA controller and on-chip PHY. The host controller enables full- and low-speed data exchange with USB devices attached to the ...
Page 19
USB_OTG Pin # Signal Name 1 VBUS 2 USB_OTG_D- 3 USB_OTG_D+ 4 USB_OTG_ID 5 GND USB OTG is a supplement to the USB 2.0 specification that augments the capability of existing mobile devices and USB peripherals by adding host functionality ...
Page 20
HEADPHONE Pin # Signal Name 1 AGND 2 IN1=IN2 3 IN2=IN1 SD/MMC Pin # Signal Name 1 Pull-up 2 SSEL1 3 MOSI1 4 VDD (power supply) 5 SCK1 6 GND 7 MISO1 8 Pull-up 9 Not connected 10 Not connected ...
Page 21
MECHANICAL DIMENSIONS: All measures are in Inches. Page 21 ...
Page 22
AVAILABLE DEMO SOFTWARE: Accelerometer Demo - Basic use of I/O, timer, interrupt controllers, LDC module and the on board accelerometer EW-ARM 5.40. Audio Device Class - USB audio device class with one output and one input EW-ARM 5.40. ...
Page 23
ORDER CODE: LPC-1766STK - How to order? You can order to us directly or by any of our distributors. Check our web Revision history: Revision Initial, October 2009 assembled and tested board www.olimex.com/dev for more info. Page 23 ...
Page 24
... However all warranties implied or expressed including but not limited to implied warranties of merchantability or fitness for purpose are excluded. This document is intended only to assist the reader in the use of the product. OLIMEX Ltd. shall not be liable for any loss or damage arising from the use of any information in this document or any error or omission in such information or any incorrect use of the product ...