Wi.232DTS-FCC-ST-R Radiotronix, Wi.232DTS-FCC-ST-R Datasheet

RF Modules & Development Tools FCC APPROVED MODULE W/ STRAIGHT RPSMA

Wi.232DTS-FCC-ST-R

Manufacturer Part Number
Wi.232DTS-FCC-ST-R
Description
RF Modules & Development Tools FCC APPROVED MODULE W/ STRAIGHT RPSMA
Manufacturer
Radiotronix
Datasheet

Specifications of Wi.232DTS-FCC-ST-R

Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
WI232DTS-FCC-ST-R
Revision
1.0.5
WI.232DTS-FCC-R and
RK-WI.232DTS-FCC-R
DATASHEET

Related parts for Wi.232DTS-FCC-ST-R

Wi.232DTS-FCC-ST-R Summary of contents

Page 1

... WI.232DTS-FCC-R and RK-WI.232DTS-FCC-R DATASHEET Revision 1.0.5 ...

Page 2

... WI.232DTS-FCC-R USER’S MANUAL WI.232DTS-FCC-R/ RK-WI.232DTS-FCC-R DATASHEET © Radiotronix 905 Messenger Lane Moore, Oklahoma 73160 Phone 405.794.7730 • Fax 405.794.7477 www.radiotronix.com 1 ...

Page 3

... DATE TRM 8/9/2005 TJE 6/13/2007 TJE 6/13/2007 DATE DESCRIPTION 8/9/2005 Document created from RK-Wi.232DTS 1.0.3 8/15/2005 Added customer manual verbiage 8/29/2005 Added FCC clarifications in Section 9 10/7/2005 Made changes to FCC verbiage per TCB 11/2/2005 Added 3dBi antenna gain limit 11/8/2005 Added restriction on LP antenna usage ...

Page 4

... LOOPBACK MODE ......................................................................................................................... 12 6. PCB LAYOUT DIAGRAMS ................................................................................................................... 13 6.1. RK-WI.232DTS-FCC-R EVALUATION BOARD LAYOUT .............................................................. 13 6.2. WI.232DTS-FCC-R EVALUATION MODULE LAYOUT .................................................................. 14 6.3. TABLE 1, WI.232DTS-FCC-R MODULE PIN OUT ......................................................................... 15 7. SCHEMATIC DIAGRAMS ..................................................................................................................... 16 7.1. WI.232DTS-FCC-R SCHEMATIC DIAGRAM.................................................................................. 16 7.2. WI.232DTS-FCC-R EVALUATION BOARD SCHEMATIC DIAGRAM ............................................ 17 8. USAGE GUIDELINES FOR FCC COMPLIANCE ................................................................................. 18 8 ...

Page 5

... WI.232DTS-FCC-R USER’S MANUAL 8.2. MODULE MODIFICATION .............................................................................................................. 18 8.3. END PRODUCT LABELING REQUIREMENTS.............................................................................. 19 8.4. ADDITIONAL FCC TESTING REQUIREMENTS ............................................................................ 19 9. FCC STATEMENTS OF COMPLIANCE ............................................................................................... 20 9.1. STATEMENTS AND CONDITIONS OF MODULAR COMPLIANCE .............................................. 20 9.2. CUSTOMER FCC WARNING REQUIREMENTS ........................................................................... 21 9.3. PRODUCT TESTING....................................................................................................................... 21 9.4. ORDERING INFORMATION ........................................................................................................... 21 9.5. CONTACT INFORMATION ............................................................................................................. 22 ...

Page 6

... WI.232DTS-FCC-R USER’S MANUAL 1. Description The RK-Wi.232DTS-FCC rapid-development/evaluation kit FCC pre-certified module, the Wi232DTS- FCC-R. When used within the guidelines presented in this document, no FCC part 15 testing/certification of the Wi232DTS-FCC-R is necessary in the end product. Included in the kit is: • 1-Rapid Development Case. • 1-Rapid Development Utility and Documentation CD. ...

Page 7

... The correct orientation of the module is with the antenna connector closest to the edge of the evaluation board. Make sure it is seated fully and correctly. • Insert the other Wi.232DTS-FCC-R module into the other evaluation board, also observing the correct polarity. ...

Page 8

... Using the RK-Wi.232DTS-FCC-R Evaluation Software The software supplied with the RK-Wi.232DTS-FCC-R RadKit is used to read and set the volatile and non-volatile registers with the Wi.232DTS module. Refer to the Wi.232DTS Users Manual for more information on the register settings. 3.1. COM Port Setup and Selection Upon starting the RK-Wi ...

Page 9

... WI.232DTS-FCC-R USER’S MANUAL To Use Wireless Chat: Type a message in the lower text field and press Enter. The text you typed will be displayed on the remote system, prefixed with a Node Identifier if you specified one. 3.3. Non-Volatile Register Page The Non-Volatile Register page in the evaluation software allows you to change the default settings which will be loaded when the module is powered on ...

Page 10

... WI.232DTS-FCC-R USER’S MANUAL 3.4. Volatile Register Page In this page, you can change the Volatile settings of the module. Values programmed into these registers are lost of power-down. The page also provides a means of switching the receiver and transmitter on and off, setting receive and transmit channels, transceiver mode and modulation settings. ...

Page 11

... To perform a read of that register, simply click the “Read” button. Descriptions of the register functions can be found in the Wi.232DTS Users Manual. 4.2. Diagnostic Command Modes There are a special class of commands available through the evaluation software. These controls are located on the “ ...

Page 12

... WI.232DTS-FCC-R USER’S MANUAL 4.4. Transmit Diagnostic Transmit Diagnostic consists of four radio buttons which select the transmit channel. Low, Mid and High are quick reference buttons which can be used to select the lowest, the middle, or the highest channel. Any specific channel can be selected by using the controls below the “Set TX Diag” button. ...

Page 13

... Loopback Mode The RK-Wi.232DTS-FCC-R kit can be operated in a loopback mode by configuring the COM jumpers in such a way as to link together the TXD and RXD lines to and from the module in the remote evaluation board. Using this mode, the user can send data from their local evaluation board and have it re-transmitted back to them by the remote evaluation board ...

Page 14

... WI.232DTS-FCC-R USER’S MANUAL 6. PCB Layout Diagrams 6.1. RK-Wi.232DTS-FCC-R Evaluation Board Layout 13 Chapter 6 ...

Page 15

... WI.232DTS-FCC-R USER’S MANUAL 6.2. Wi.232DTS-FCC-R Evaluation Module Layout JP1 Pin 1 NOTE: Pin 1 of the Wi.232DTS-FCC-R module’s JP2 aligns with Pin 1 of JP6 on the evaluation board. The following table lists the pin numbers and their assignments. 14 JP2 Pin 1 ...

Page 16

... WI.232DTS-FCC-R USER’S MANUAL 6.3. Table 1, Wi.232DTS-FCC-R Module Pin Out Pin Name JP2 Pin 1 JP2 Pin 2 JP2 Pin 3 JP2 Pin 4 JP2 Pin 5 JP2 Pin 6 JP2 Pin 7 JP2 Pin 8 JP2 Pin 9 JP2 Pin 10 JP2 Pin 11 JP2 Pin 12 JP1 Pin 1 JP1 Pin 2 JP1 Pin 3 ...

Page 17

... WI.232DTS-FCC-R USER’S MANUAL 7. Schematic Diagrams 7.1. Wi.232DTS-FCC-R Schematic Diagram 16 Chapter 7 ...

Page 18

... WI.232DTS-FCC-R USER’S MANUAL 7.2. Wi.232DTS-FCC-R Evaluation Board Schematic Diagram 17 ...

Page 19

... WI.232DTS-FCC-R USER’S MANUAL 8. Usage Guidelines for FCC Compliance The Wi.232DTS-FCC-R modules included in this rapid development kit have been awarded a FCC modular approval. That means that this module, when integrated into your end product, requires no FCC part 15 testing as long as the following guidelines are met. Failure to meet any of the following guidelines will prevent the inheritance of the FCC modular certification ...

Page 20

... WI.232DTS-FCC-R USER’S MANUAL 8.3. End Product Labeling Requirements Pursuant to FCC public notice DA 00-1407, the end product must be labeled on its exterior with the following verbiage: “Contains FCC ID: Q7V-3F090003X” 8.4. Additional FCC Testing Requirements While the module’s FCC certification can be inherited (presuming the guidelines are met), additional testing will be required to achieve full FCC compliance for your end-product ...

Page 21

... Any changes or modifications not expressly approved by Radiotronix, Inc. could void the user’s authority to operate the equipment. The Wi.232DTS-FCC-R module is provided with an inheritable FCC Modular Certification. This certification may be inherited in an end-user product, negating the need for FCC part 15 intentional radiator testing on this module, provided that the following guidelines are met approved antenna must be directly coupled to the module’ ...

Page 22

... The integrator must still show that their product complies with FCC regulations applicable to their product. The integrator is not required to perform transmitter testing on the Wi.232DTS-FCC-R module, provided the guidelines in this document are met. 9.4. Ordering Information PRODUCT PART NUMBER Wi.232DTS-FCC-ST-R Wi.232DTS-FCC-RA-R DESCRIPTION Straight angle connector Right angle connector ...

Page 23

... WI.232DTS-FCC-R USER’S MANUAL 9.5. Contact Information Corporate Headquarters: 905 Messenger Lane Moore, Oklahoma 73160 405-794-7730 website: www.radiotronix.com support: support@radiotronix.com 22 ...

Related keywords