S29GL01GP12TFI010 Spansion Inc., S29GL01GP12TFI010 Datasheet - Page 33

• Manufacturer Part Number: S29GL01GP12TFI010
• Description: Flash 3V 1 Gb Mirrorbit highest address120ns
• Manufacturer: Spansion Inc.

Specifications of S29GL01GP12TFI010

• Memory Type: NOR
• Memory Size: 1 Gbit
• Access Time: 110 ns
• Data Bus Width: 8 bit, 16 bit
• Architecture: Uniform
• Interface Type: Page-mode
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 2.7 V
• Maximum Operating Current: 50 mA
• Mounting Style: SMD/SMT
• Operating Temperature: + 85 C
• Package / Case: TSOP-56
• Memory Configuration: 128K X 16
• Ic Interface Type: Parallel
• Supply Voltage Range: 2.7V To 3.6V
• Memory Case Style: BGA
• No. Of Pins: 56
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

November 28, 2007 S29GL-P_00_A8
7.7.5
Erase Suspend/Erase Resume Commands
The Erase Suspend command allows the system to interrupt a sector erase operation and then read data
from, or program data to, any sector not selected for erasure. The sector address is required when writing this
command. This command is valid only during the sector erase operation, including the minimum t
period during the sector erase command sequence. The Erase Suspend command is ignored if written during
the chip erase operation.
When the Erase Suspend command is written during the sector erase operation, the device requires a
maximum of 20 µs (5 µs typical) to suspend the erase operation. However, when the Erase Suspend
command is written during the sector erase time-out, the device immediately terminates the time-out period
and suspends the erase operation.
After the erase operation has been suspended, the device enters the erase-suspend-read mode. The system
can read data from or program data to any sector not selected for erasure. (The device “erase suspends” all
sectors selected for erasure.) Reading at any address within erase-suspended sectors produces status
information on DQ7-DQ0. The system can use DQ7, or DQ6, and DQ2 together, to determine if a sector is
actively erasing or is erase-suspended. Refer to
After an erase-suspended program operation is complete, the device returns to the erase-suspend-read
mode. The system can determine the status of the program operation using write operation status bits, just as
in the standard program operation.
In the erase-suspend-read mode, the system can also issue the Autoselect command sequence. Refer to
Write Buffer Programming on page 26
To resume the sector erase operation, the system must write the Erase Resume command. The address of
the erase-suspended sector is required when writing this command. Further writes of the Resume command
are ignored. Another Erase Suspend command can be written after the chip has resumed erasing.
Software Functions and Sample Code
The following is a C source code example of using the erase suspend function. Refer to the Spansion Low
Level Driver User’s Guide (available on www.spansion.com) for general information on Spansion Flash
memory software development guidelines.
The following is a C source code example of using the erase resume function. Refer to the Spansion Low
Level Driver User’s Guide (available on www.spansion.com) for general information on Spansion Flash
memory software development guidelines.
/* Example: Erase suspend command */
/* Example: Erase resume command */
*( (UINT16 *)base_addr ) = 0x00B0;
*( (UINT16 *)sector_addr ) = 0x0030;
/* The flash needs adequate time in the resume state */
Cycle
Cycle
1
1
D a t a
Operation
S h e e t
Operation
Write
Write
S29GL-P MirrorBit
( P r e l i m i n a r y )
(LLD Function = lld_EraseSuspendCmd)
(LLD Function = lld_EraseResumeCmd)
and the
Table 7.10 Erase Suspend
Table 7.11 Erase Resume
Sector Address
Byte Address
Byte Address
Base + XXXh
/* write suspend command
/* write resume command
®
Autoselect on page 21
Table 7.35
Flash Family
for information on these status bits.
Sector Address
Word Address
Word Address
Base + XXXh
for details.
*/
*/
00B0h
0030h
Data
Data
SEA
time-out
33