S29GL256P11TFI010 Spansion Inc., S29GL256P11TFI010 Datasheet - Page 33

• Manufacturer Part Number: S29GL256P11TFI010
• Description: Flash 3V 256Mb Mirrorbit highest address110ns
• Manufacturer: Spansion Inc.

Specifications of S29GL256P11TFI010

• Memory Type: NOR
• Memory Size: 256 Mbit
• Access Time: 110 ns
• Data Bus Width: 8 bit, 16 bit
• Architecture: Uniform
• Interface Type: Page-mode
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 2.7 V
• Maximum Operating Current: 50 mA
• Mounting Style: SMD/SMT
• Operating Temperature: + 85 C
• Package / Case: TSOP-56
• Memory Configuration: 128K X 16
• Ic Interface Type: Parallel
• Supply Voltage Range: 2.7V To 3.6V
• Memory Case Style: TSOP
• No. Of Pins: 56
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

7.8
November 21, 2006 S29GL-P_00_A3
7.8.1
Write Operation Status
DQ7: Data# Polling
The device provides several bits to determine the status of a program or erase operation. The following
subsections describe the function of DQ1, DQ2, DQ3, DQ5, DQ6, and DQ7.
The Data# Polling bit, DQ7, indicates to the host system whether an Embedded Program or Erase algorithm
is in progress or completed, or whether the device is in Erase Suspend. Data# Polling is valid after the rising
edge of the final WE# pulse in the command sequence. Note that the Data# Polling is valid only for the last
word being programmed in the write-buffer-page during Write Buffer Programming. Reading Data# Polling
status on any word other than the last word to be programmed in the write-buffer-page returns false status
information.
During the Embedded Program algorithm, the device outputs on DQ7 the complement of the datum
programmed to DQ7. This DQ7 status also applies to programming during Erase Suspend. When the
Embedded Program algorithm is complete, the device outputs the datum programmed to DQ7. The system
must provide the program address to read valid status information on DQ7. If a program address falls within a
protected sector, Data# polling on DQ7 is active for approximately 1 µs, then that sector returns to the read
mode.
During the Embedded Erase Algorithm, Data# polling produces a “0” on DQ7. When the Embedded Erase
algorithm is complete, or if the device enters the Erase Suspend mode, Data# Polling produces a “1” on DQ7.
The system must provide an address within any of the sectors selected for erasure to read valid status
information on DQ7.
After an erase command sequence is written, if all sectors selected for erasing are protected, Data# Polling
on DQ7 is active for approximately 100 µs, then the device returns to the read mode. If not all selected
sectors are protected, the Embedded Erase algorithm erases the unprotected sectors, and ignores the
selected sectors that are protected. However, if the system reads DQ7 at an address within a protected
sector, the status may not be valid.
Just prior to the completion of an Embedded Program or Erase operation, DQ7 may change with DQ6-DQ0
while Output Enable (OE#) is asserted low. That is, the device may change from providing status information
Cycle
/* Example: Unlock Bypass Program Command
/* Do while in Unlock Bypass Entry Mode!
Cycle
/* Example: Unlock Bypass Exit Command */
D a t a
1
2
1
2
*( (UINT16 *)base_addr + 0x555 ) = 0x00A0;
*( (UINT16 *)pa )
/* Poll until done or error.
/* If done and more to program, */
/* do above two cycles again.
*( (UINT16 *)base_addr + 0x000 ) = 0x0090;
*( (UINT16 *)base_addr + 0x000 ) = 0x0000;
S h e e t
Program Setup Command
Program Command
Reset Cycle 1
Reset Cycle 2
Description
Description
( A d v a n c e
S29GL-P MirrorBit
(LLD Function = lld_UnlockBypassProgramCmd)
(LLD Function = lld_UnlockBypassResetCmd)
Table 7.15 Unlock Bypass Program
Table 7.16 Unlock Bypass Reset
*/
*/
= data;
I n f o r m a t i o n )
TM
*/
*/
Flash Family
Operation
Operation
Write
Write
Write
Write
/* write program setup command
/* write data to be programmed
Program Address
Word Address
Word Address
Base +xxxh
Base +xxxh
Base +xxxh
*/
*/
Program Data
00A0h
0090h
0000h
Data
Data
31