EP5368QI Enpirion, EP5368QI Datasheet - Page 9

Switching Converters, Regulators & Controllers 600mA BUCK REGULATOR INTEGRATED INDUCTOR

EP5368QI

Manufacturer Part Number
EP5368QI
Description
Switching Converters, Regulators & Controllers 600mA BUCK REGULATOR INTEGRATED INDUCTOR
Manufacturer
Enpirion
Datasheet

Specifications of EP5368QI

Output Voltage
0.8 V to 3.3 V
Output Current
600 mA
Input Voltage
2.4 V to 5.5 V
Switching Frequency
4 MHz
Operating Temperature Range
- 40 C to + 85 C
Mounting Style
SMD/SMT
Duty Cycle (max)
100 %
Package / Case
QFN-16
Lead Free Status / RoHS Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
EP5368QI
Manufacturer:
Voltronics
Quantity:
20 000
Part Number:
EP5368QI
Manufacturer:
ALTERA
0
Part Number:
EP5368QI
Manufacturer:
ENPIRION
Quantity:
20 000
Part Number:
EP5368QI
Manufacturer:
ENPIRIO
Quantity:
13 373
Part Number:
EP5368QI
0
Company:
Part Number:
EP5368QI
Quantity:
371
When operating in VID mode, the maximum
total capacitance on the output, including the
output filter capacitor and bulk and decoupling
capacitance, at the load, is given as:
C
When
programmed using and external resistor divider
the maximum total capacitance on the output is
given as:
C
The above number and formula assume a no
load condition at startup.
Over Current/Short Circuit Protection
The current limit function is achieved by
sensing the current flowing through a sense P-
MOSFET which is compared to a reference
current. When this level is exceeded the P-
FET is turned off and the N-FET is turned on,
pulling V
for a period of 1mS and then a normal soft start
is initiated. If the over current condition still
persists, this cycle will repeat in a “hiccup”
mode.
Application Information
Output Voltage Select
To provide the highest degree of flexibility in
choosing output voltage, the EP5368QI uses a
3 pin VID, or Voltage ID, output voltage select
arrangement.
choose one of seven preset voltages, or to use
an external voltage divider.
output of the VID multiplexer sets the value for
the voltage reference DAC, which in turn is
connected to the non-inverting input of the
error amplifier. This allows the use of a single
feedback divider with constant loop gain and
optimum compensation, independent of the
output
Enpirion 2010 all rights reserved, E&OE
03260
OUT_TOTAL_MAX
OUT_TOTAL_MAX
the
OUT
low. This condition is maintained
EP5368QI
= C
= 1.251x10
This allows the designer to
OUT_Filter
voltage
-3
+ C
output
/V
OUT
OUT_BULK
Internally, the
Farads
voltage
selected.
= 700uF
is
09/23/2010
9
Under Voltage Lockout
During initial power up an under voltage
lockout circuit will hold-off the switching
circuitry until the input voltage reaches a
sufficient level to insure proper operation. If
the voltage drops below the UVLO threshold,
the lockout circuitry will again disable the
switching.
chattering between states.
Enable
The ENABLE pin provides a means to shut
down
operation. A logic low will disable the converter
and cause it to shut down. A logic high will
enable the converter into normal operation. In
shutdown mode, the device quiescent current
will be less than 1 uA.
NOTE: This pin must not be left floating.
Thermal Shutdown
When excessive power is dissipated in the
chip, the junction temperature rises. Once the
junction temperature exceeds the thermal
shutdown temperature the thermal shutdown
circuit turns off the converter output voltage
thus allowing the device to cool. When the
junction temperature decreases by 15C, the
device will go through the normal startup
process.
Table 1 shows the various VS0-VS2 pin logic
states and the associated output voltage
levels. A logic “1” indicates a connection to
VIN or to a “high” logic voltage level. A logic
“0” indicates a connection to ground or to a
“low” logic voltage level. These pins can be
either hardwired to VIN or GND or alternatively
can be driven by standard logic levels. Logic
low is defined as VLOW ≤ 0.4V. Logic high is
defined as VHIGH ≥ 1.4V. Any level between
these two values is indeterminate. These pins
must not be left floating.
the
Hysteresis is included to prevent
converter
or
www.enpirion.com
enable
EP5368QI
normal
Rev: F

Related parts for EP5368QI