B43305B2158M EPCOS Inc, B43305B2158M Datasheet

Page 1

... Aluminum electrolytic capacitors Snap-in capacitors Series/Type: B43305 Date: November 2008 © EPCOS AG 2008. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. ...

Page 2

... Different case sizes available for each capacitance value RoHS-compatible Construction Charge/discharge-proof, polar Aluminum case, fully insulated with PVC Version with PET insulation available Version with additional PET insulation cap on terminal side available for insulating the capacitor from the PCB Snap-in solder pins to hold component in place on PC-board ...

Page 3

... Characteristics at low Max. impedance ratio temperature at 100 Hz IEC climatic category To IEC 60068- The capacitors can be operated in the temperature range of consideration. Detail specification Similar to CECC 30301-806 Sectional specification IEC 60384-4 Please read Cautions and warnings and Important notes at the end of this document. ...

Page 4

... B43305 Ultra compact Dimensional drawings Snap-in capacitors with standard insulation (PVC or PET) Snap-in terminals, length 6.3 1 mm. Also available in a shorter version with a length of 4.5 1 mm. PET insulation is marked with label "PET" on the sleeve. Dimensions (mm) Approx. weight ( Please read Cautions and warnings and Important notes at the end of this document ...

Page 5

... Snap-in capacitors with PVC insulation and PET insulation cap on terminal side Snap-in terminals, length 6.3 +1/ 1.4 mm. Also available in a shorter version with a length of 4.5 1.4 mm. PET insulation cap is positioned under the insulation sleeve. Dimensions (mm) Approx. weight (g) d +1.4 l +2. Please read Cautions and warnings and Important notes at the end of this document ...

Page 6

... B43305 Ultra compact Packing of snap-in capacitors For ecological reasons the packing is pure cardboard. Components can be withdrawn (in full or in part) in the correct position for insertion. Ordering codes for terminal styles and insulation features Identification in 3rd block of ordering code Snap-in capacitors Terminal version Standard terminals 6 ...

Page 7

Overview of available types V (V DC) 200 R Case dimensions 100 120 150 180 220 270 330 22 25 390 22 25 470 560 ...

Page 8

B43305 Ultra compact V (V DC) 200 R Case dimensions 1000 1200 1500 1800 30 ...

Page 9

... Hz) = 1.03 I (100 Hz Page B43305 Ordering code AC,R (composition see below) B43305A2337M0*# B43305A2397M0*# B43305A2477M0*# B43305B2477M0*# B43305A2567M0*# B43305B2567M0*# B43305A2687M0*# B43305B2687M0*# B43305C2687M0*# B43305A2827M0*# B43305B2827M0*# B43305C2827M0*# B43305A2108M0*# B43305B2108M0*# B43305C2108M0*# B43305D2108M0*# B43305A2128M0*# B43305B2128M0*# B43305C2128M0*# B43305A2158M0*# B43305B2158M0*# B43305C2158M0*# B43305A2188M0*# B43305B2188M0*# B43305A2228M0*# B43305B2228M0*# B43305A2278M0*# B43305A2338M0*# ...

Page 10

B43305 Ultra compact Technical data and ordering codes C Case ESR R 100 Hz dimensions 100 250 270 22 25 470 330 22 30 380 ...

Page 11

Technical data and ordering codes C Case ESR R 100 Hz dimensions 100 400 1990 1650 100 22 25 ...

Page 12

B43305 Ultra compact Technical data and ordering codes C Case ESR R 100 Hz dimensions 100 450 1990 1650 ...

Page 13

Useful life depending on ambient temperature T Voltage derating (0. enables 105 C operation R Frequency factor of permissible ripple current I versus frequency Refer to chapter "General technical information, 5.3 Calculation of useful life" ...

Page 14

B43305 Ultra compact Impedance Z versus frequency f Typical behavior Please read Cautions and warnings and Important notes at the end of this document Page ...

Page 15

... However, the amount of dangerous materials used in our products has been limited to an absolute minimum. Nevertheless, the following rules should be observed when handling Al electrolytic capacitors: Any escaping electrolyte should not come into contact with eyes or skin. If electrolyte does come into contact with the skin, wash the affected parts immediately with running water ...

Page 16

... Do not exceed the specified time or temperature limits during soldering. Please read Cautions and warnings and Important notes at the end of this document Page Reference Chapter "General technical information" 1 "Basic construction of aluminum electrolytic capacitors" 3.1.6 "Reverse voltage" 7.2 "Maximum permissible operating temperature" 10 "Maintenance" 11.1 "Mounting positions of capacitors with screw terminals" ...

Page 17

... Topic Safety information Soldering, Do not allow halogenated hydrocarbons to come cleaning agents into contact with aluminum electrolytic capacitors. Passive Avoid external energy, such as fire or electricity. flammability Active Avoid overload of the capacitors. flammability Breakdown strength Do not damage the insulating sleeve, especially of insulating when ring clips are used for mounting. ...

Page 18

B43305 Ultra compact Symbols and terms Symbol English C Capacitance C Rated capacitance R C Series capacitance S C Series capacitance at temperature T S,T C Capacitance at frequency Case diameter, nominal dimension d Maximum case diameter ...

Page 19

Symbol English V Voltage V Forming voltage F V Operating voltage op V Rated voltage, DC voltage R V Surge voltage S X Capacitive reactance C X Inductive reactance L Z Impedance Z Impedance at temperature T T tan Dissipation ...

Page 20

Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical ...