2035XD Applied Motion, 2035XD Datasheet
2035XD
Manufacturer Part Number
2035XD
Description
Stepper Drives 2 Axis 2.0A 35VDC
Manufacturer
Applied Motion
Datasheet
1.2035XD.pdf
(2 pages)
Specifications of 2035XD
Motor Drive Type
2035xd Dual Step
Supply Voltage
12 V to 35 V
Steps Resolution Per Revolution
200 to 50800
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
STEPPER
DRIVES
2035XD Step Motor Drive with Oscillator
2 Axis Full, Half and Microstep
Programmable Digital Oscillator
or Pulse Direction
2.0 amps, 35 VDC
Features
Description
• DC bus voltage 12-35 VDC motor supply (includ-
• Software programmable motor current, 0.1–2.0
• Software programmable step size, 200–50800
• Automatic idle current reduction
• Four optically isolated digital inputs: step/run 1,
• Two analog inputs, 10 bit resolution, 0 - 5VDC
• On-board oscillator generates step pulses and
• Fixed speed or proportional to analog input
• Optically isolated 5–24 VDC Tach output for
• 70 watts of usable power per axis
• Screw terminal connectors
• Dual H-bridge, inaudible PWM amplifier
• 3 state, pulse width modulated current control,
• Drives 4, 6 or 8 lead size 11, 14, 17 or 23 step
The 2035XD step motor driver is a two axis, soft-
ware configured step/direction or oscillator drive.
Drives can be quickly and precisely configured us-
ing our eXposition™ software and a Windows PC.
When configured for pulse/direction mode, the two
drives can be commanded by the step and direction
signals available from many PLCs and step motor
indexers.
In oscillator mode, the two drives generate their
own acceleration and deceleration profiles and are
commanded by digital run/stop signals. These sig-
nals can be supplied by PLCs, mechanical
switches, single board computers or other motion
control devices. Speeds may be fixed or can be set
“on the fly” by 0 to 5 volt analog signals.
ing ripple)
amps/phase
steps/rev
step/run 2, direction 1, direction 2
accel/decel ramps
monitoring speed
switching at 20–30 KHz
motors
MECHANICAL OUTLINE
2x Ø.125
BLOCK DIAGRAM
Recommended motors for the 2035XD drive:
Size 11
———— ———— ———— ————
HT11-012 5014-842
HT11-013
10 - 35 VDC
ANALOG1 IN
ANALOG2 IN
STEP/RUN1
STEP/RUN2
0.25"
+5V OUT
831/761-6555 • 800/525-1609 • FAX 831/761-6544
DIR1
DIR2
GND
OUT
PC
.875"
1.50"
Size 14
Isolation
Optical
Filter
404 Westridge Dr. • Watsonville, CA 95076
3.70"
0.15"
Internal
Supply
Logic
Controller
www.appliedmotionproducts.com
0.125"
RS232
Size 17
HT17-068 HT23-394
HT17-071 HT23-397
HT17-075 HT23-400
2 Axis
3.75"
eeprom
Amplifier
Amplifier
2.50"
Size 23
Power
Power
3.00"
PWM
PWM
4x Ø.125
motor
motor
4.00"
0.25"
Related parts for 2035XD
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Stepper Drives 2.0A 12-35VDC
Manufacturer:
Applied Motion
Datasheet:
Part Number:
Description:
AC, DC & Servo Motors Nema 17, 45mm, 50W 5000 RPM, 48V
Manufacturer:
Applied Motion
Part Number:
Description:
AC, DC & Servo Motors 7A Cont, 14A Pk, Si Programmer w/Qk Tune
Manufacturer:
Applied Motion
Part Number:
Description:
AC, DC & Servo Motors Nema 23, 104mm, 200W 3350 RPM, 48V
Manufacturer:
Applied Motion
Part Number:
Description:
AC, DC & Servo Motors 7A Cont, 14A Pk, S Pulse & Direction
Manufacturer:
Applied Motion
2035XD Summary of contents
Page 1
... KHz • Drives lead size 11, 14 step motors Description The 2035XD step motor driver is a two axis, soft- ware configured step/direction or oscillator drive. Drives can be quickly and precisely configured us- ing our eXposition™ software and a Windows PC. When configured for pulse/direction mode, the two ...
Page 2
... Torque Curves HT11-012 MOTOR Motor Connection: 4 Lead Bipolar Drive Setting: Full Resolution • 1.0 A/Phase 10 Dynamic Torque 5 (oz-in rev/sec 5014-842 MOTOR Motor Connection: Parallel Drive Setting: Full Resolution • 1.0 A/Phase 25 20 Dynamic 15 Torque (oz-in rev/sec HT17-071 MOTOR Motor Connection: Parallel Drive Setting: Full Resolution • ...