LME0305SC Murata Power Solutions Inc, LME0305SC Datasheet - Page 2

• Manufacturer Part Number: LME0305SC
• Description: DC/DC Converters & Regulators 250mW SIP 3.3V/5V Single Output
• Manufacturer: Murata Power Solutions Inc
• Series: LMEr

Specifications of LME0305SC

• Output Power: 0.25 W
• Input Voltage Range: 2.97 V to 3.63 V
• Input Voltage (nominal): 3.3 V
• Number Of Outputs: 1
• Output Voltage (channel 1): 5 V
• Output Current (channel 1): 50 mA
• Isolation Voltage: 1 KV
• Package / Case Size: SIP-4
• Output Voltage: 5 V
• Product: Isolated
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

TEMPERATURE CHARACTERISTICS
Parameter
Specification
Storage
Cooling
TEMPERATURE DERATING GRAPH
TECHNICAL NOTES
ISOLATION VOLTAGE
‘Hi Pot Test’, ‘Flash Tested’, ‘Withstand Voltage’, ‘Proof Voltage’, ‘Dielectric Withstand Voltage’ & ‘Isolation Test Voltage’ are all terms that relate to the same thing, a test voltage,
applied for a specified time, across a component designed to provide electrical isolation, to verify the integrity of that isolation.
Murata Power Solutions LME series of DC/DC converters are all 100% production tested at their stated isolation voltage. This is 1kVDC for 1 second.
A question commonly asked is, “What is the continuous voltage that can be applied across the part in normal operation?”
For a part holding no specific agency approvals, such as the LME series, both input and output should normally be maintained within SELV limits i.e. less than 42.4V peak, or
60VDC. The isolation test voltage represents a measure of immunity to transient voltages and the part should never be used as an element of a safety isolation system. The part
could be expected to function correctly with several hundred volts offset applied continuously across the isolation barrier; but then the circuitry on both sides of the barrier must
be regarded as operating at an unsafe voltage and further isolation/insulation systems must form a barrier between these circuits and any user-accessible circuitry according to
safety standard requirements.
REPEATED HIGH-VOLTAGE ISOLATION TESTING
It is well known that repeated high-voltage isolation testing of a barrier component can actually degrade isolation capability, to a lesser or greater degree depending on materials,
construction and environment. The LME series has toroidal isolation transformers, with no additional insulation between primary and secondary windings of enameled wire. While
parts can be expected to withstand several times the stated test voltage, the isolation capability does depend on the wire insulation. Any material, including this enamel (typically
polyurethane) is susceptible to eventual chemical degradation when subject to very high applied voltages thus implying that the number of tests should be strictly limited. We
therefore strongly advise against repeated high voltage isolation testing, but if it is absolutely required, that the voltage be reduced by 20% from specified test voltage.
This consideration equally applies to agency recognized parts rated for better than functional isolation where the wire enamel insulation is always supplemented by a further
insulation system of physical spacing or barriers.
RoHS COMPLIANT INFORMATION
www.murata-ps.com
0.375
0.250
0.125
0
0
Safe Operating
Ambient Temperature (°C)
Area
50
70°C
Conditions
All output types
Free air convection
100
125°C
150
TOLERANCE ENVELOPE
+10%
This series is compatible with RoHS soldering systems with a peak wave solder temperature of
300°C for 10 seconds. The pin termination finish on the SIP package type is Tin Plate, Hot Dipped
over Matte Tin with Nickel Preplate. The DIP types are Matte Tin over Nickel Preplate. Both types in
this series are backward compatible with Sn/Pb soldering systems.
For further information, please visit www.murata-ps.com/rohs
+5%
V
NOM
10
25
Output Load Current (%)
50
Isolated 250mW Single Output DC/DC Converters
75
Technical enquiries - email: [e-mail], tel:
100
+2.5%
-2.5%
-7.5%
Min.
-55
0
Typ.
LME Series
KDC_LMEC_E03 Page 2 of 5
Max.
130
70
[phone]
Units
°C