PIC18F26K80-I/SO Microchip Technology, PIC18F26K80-I/SO Datasheet - Page 402

• Manufacturer Part Number: PIC18F26K80-I/SO
• Description: MCU PIC 64KB FLASH 28SOIC
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F26K80-I/SO

• Core Size: 8-Bit
• Program Memory Size: 64KB (32K x 16)
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Core Processor: PIC
• Speed: 64MHz
• Connectivity: ECAN, I²C, LIN, SPI, UART/USART
• Number Of I /o: 24
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 3.6K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 8x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (0.300", 7.50mm Width)
• Controller Family/series: PIC18
• Ram Memory Size: 4KB
• Cpu Speed: 16MIPS
• No. Of Pwm Channels: 5
• Embedded Interface Type: I2C, SPI, USART
• Processor Series: PIC18F26K80
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: I2C, SPI, USART
• Maximum Clock Frequency: 64 MHz
• Number Of Programmable I/os: 24
• Number Of Timers: 5
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

PIC18F66K80 FAMILY
REGISTER 27-3:
DS39977C-page 402
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7-6
bit 5
bit 4-0
Note 1:
MDSEL1
R/W-0
2:
3:
(1)
These bits can only be changed in Configuration mode. See
This bit is used in Mode 2 only.
If FIFO is configured to contain four or less buffers, then the FIFO interrupt will trigger.
MDSEL<1:0>: Mode Select bits
00 = Legacy mode (Mode 0, default)
01 = Enhanced Legacy mode (Mode 1)
10 = Enhanced FIFO mode (Mode 2)
11 = Reserved
FIFOWM: FIFO High Water Mark bit
1 = Will cause FIFO interrupt when one receive buffer remains
0 = Will cause FIFO interrupt when four receive buffers remain
EWIN<4:0>: Enhanced Window Address bits
These bits map the group of 16 banked CAN SFRs into Access Bank addresses, 0F60-0F6Dh. The
exact group of registers to map is determined by the binary value of these bits.
Mode 0:
Unimplemented: Read as ‘ 0 ’
Mode 1, 2:
00000 = Acceptance Filters 0, 1, 2 and BRGCON2, 3
00001 = Acceptance Filters 3, 4, 5 and BRGCON1, CIOCON
00010 = Acceptance Filter Masks, Error and Interrupt Control
00011 = Transmit Buffer 0
00100 = Transmit Buffer 1
00101 = Transmit Buffer 2
00110 = Acceptance Filters 6, 7, 8
00111 = Acceptance Filters 9, 10, 11
01000 = Acceptance Filters 12, 13, 14
01001 = Acceptance Filter 15
01010 - 01110 = Reserved
01111 = RXINT0, RXINT1
10000 = Receive Buffer 0
10001 = Receive Buffer 1
10010 = TX/RX Buffer 0
10011 = TX/RX Buffer 1
10100 = TX/RX Buffer 2
10101 = TX/RX Buffer 3
10110 = TX/RX Buffer 4
10111 = TX/RX Buffer 5
11000 - 11111 = Reserved
MDSEL0
R/W-0
ECANCON: ENHANCED CAN CONTROL REGISTER
(1)
W = Writable bit
‘1’ = Bit is set
FIFOWM
R/W-0
(2)
EWIN4
(1)
R/W-1
Preliminary
(2)
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
EWIN3
R/W-0
Register 27-1
EWIN2
R/W-0
(3)
to change to Configuration mode.
 2011 Microchip Technology Inc.
x = Bit is unknown
EWIN1
R/W-0
EWIN0
R/W-0
bit 0