LPC1768FET100,551 NXP Semiconductors, LPC1768FET100,551 Datasheet - Page 25

• Manufacturer Part Number: LPC1768FET100,551
• Description: IC MCU 32BIT 512KB FLASH 100LQFP
• Manufacturer: NXP Semiconductors
• Series: LPC17xxr

Specifications of LPC1768FET100,551

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 100MHz
• Connectivity: CAN, Ethernet, I²C, IrDA, Microwire, SPI, SSI, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, Motor Control PWM, POR, PWM, WDT
• Number Of I /o: 70
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 2.4 V ~ 3.6 V
• Data Converters: A/D 8x12b, D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Processor Series: LPC1768
• Core: ARM Cortex-M3
• Data Bus Width: 32 bit
• Data Ram Size: 16 KB
• Interface Type: Ethernet, USB, CAN, I2S, I2C
• Maximum Clock Frequency: 100 MHz
• Number Of Programmable I/os: 70
• Number Of Timers: 4
• Maximum Operating Temperature: + 150 C
• Mounting Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 568-5215

NXP Semiconductors
LPC1769_68_67_66_65_64_63
Product data sheet
7.12.2.1 Features
7.12.3.1 Features
7.12.2 USB host controller
7.12.3 USB OTG controller
7.13 CAN controller and acceptance filters
The host controller enables full- and low-speed data exchange with USB devices attached
to the bus. It consists of a register interface, a serial interface engine, and a DMA
controller. The register interface complies with the OHCI specification.
USB OTG is a supplement to the USB 2.0 specification that augments the capability of
existing mobile devices and USB peripherals by adding host functionality for connection to
USB peripherals.
The OTG Controller integrates the host controller, device controller, and a master-only
I
interface controls an external OTG transceiver.
Remark: The CAN controllers are available on parts LPC1769/68/66/65/64. See
The Controller Area Network (CAN) is a serial communications protocol which efficiently
supports distributed real-time control with a very high level of security. Its domain of
application ranges from high-speed networks to low cost multiplex wiring.
The CAN block is intended to support multiple CAN buses simultaneously, allowing the
device to be used as a gateway, switch, or router among a number of CAN buses in
industrial or automotive applications.
2
•
•
•
•
•
•
•
•
•
C-bus interface to implement OTG dual-role device functionality. The dedicated I
•
•
•
•
Endpoint Maximum packet size selection (up to USB maximum specification) by
software at run time.
Supports SoftConnect and GoodLink features.
While USB is in the Suspend mode, the part can enter one of the reduced power
modes and wake up on USB activity.
Supports DMA transfers with all on-chip SRAM blocks on all non-control endpoints.
Allows dynamic switching between CPU-controlled slave and DMA modes.
Double buffer implementation for Bulk and Isochronous endpoints.
OHCI compliant.
One downstream port.
Supports port power switching.
Fully compliant with On-The-Go supplement to the USB 2.0 Specification, Revision
1.0a.
Hardware support for Host Negotiation Protocol (HNP).
Includes a programmable timer required for HNP and Session Request Protocol
(SRP).
Supports any OTG transceiver compliant with the OTG Transceiver Specification
(CEA-2011), Rev. 1.0.
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 5 April 2011
LPC1769/68/67/66/65/64/63
32-bit ARM Cortex-M3 microcontroller
© NXP B.V. 2011. All rights reserved.
Table
2
C-bus
25 of 79
2.