270-40.2-RC Xicon, 270-40.2-RC Datasheet - Page 3

Metal Film Resistors - Through Hole 40.2ohms 1% 50PPM

270-40.2-RC

Manufacturer Part Number
270-40.2-RC
Description
Metal Film Resistors - Through Hole 40.2ohms 1% 50PPM
Manufacturer
Xicon
Series
270r
Datasheet

Specifications of 270-40.2-RC

Resistance
40.2 Ohms
Tolerance
1 %
Power Rating
0.125 Watt (1/8 Watt)
Voltage Rating
200 Volts
Termination Style
Axial
Operating Temperature Range
- 55 C to + 155 C
Dimensions
1.85 mm Dia. x 3.5 mm L
Temperature Coefficient
+/- 50 PPM / C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
XC-600046
Metal Film Fixed Resistors (RoHS Compliant)
Characteristics
Terminal
strength
Resistance to
soldering heat
Solderability
Resistance to
solvent
Temperature
cycling
Load life in
humidity
Load life
CHARACTERISTICS (Cont.)
Specifications are subject to change without notice. No liability or warranty implied by this information. Environmental compliance based on producer documentation.
With no evidence of mechanical
damage.
Resistance change rate is
± (1% + 0.05Ω) Max. with no
evidence of mechanical damage.
95 % coverage Min.
No deterioration of protective
coatings and markings.
Resistance change rate is
± (1% + 0.05Ω) Max. with no
evidence of mechanical damage.
Resistance value
Normal type
Resistance value
Normal type
XICON PASSIVE COMPONENTS • (800) 628-0544
Limits
± 1.5 %
± 1.5 %
∆R/R
∆R/R
Test Methods ( JIS C 5201-1 )
6.1 Direct load
Resistance to a 2.5 kgs direct load for 10 secs.
in the direction of the longitudinal axis of the terminal leads.
Twist test :
Terminal leads shall be bent through 90° at a point of about
6mm from the body of the resistor and shall be rotated through 360°
about the original axis of the bent terminal in alternating direction
for a total of 3 rotations.
6.4 Permanent resistance change when leads
immersed to 3.2 to 4.8 mm from the body in
350 °C ± 10°C solder for 3 ± 0.5 seconds
6.5 The area covered with a new , smooth
clean , shiny and continuous surface free
from concentrated pinholes.
Test temp. of solder : 245°C ± 3°C
Dwell time in solder : 2 ~ 3 seconds
6.9 Specimens shall be immersed in a bath of
trichroethane completely for 3 minutes with
ultrasonic.
7.4 Resistance change after continuous
5 cycles for duty shown below:
StepTemperature
7.9 Resistance change after 1,000 hours
operating at RCWV with duty cycle of
(1.5 hours "on", 0.5 hour "off") in a humidity
test chamber controlled at 40°C ± 2°C
and 90 to 95 % relative humidity
7.10 Permanent resistance change after
1,000 hours operating at RCWV with duty
cycle of ( 1.5 hours "on", 0.5 hour "off" ) at
70°C ± 2°C ambient
1
2
3
4
+155°C ±2°C
Room temp.
Room temp.
-55°C ±3°C
Time
MF-RC Series
Date Revised: 9/28/05
10~15 mins
10~15 mins
30 mins
30 mins

Related parts for 270-40.2-RC