EPM7064STC44-5N Altera, EPM7064STC44-5N Datasheet - Page 48

• Manufacturer Part Number: EPM7064STC44-5N
• Description: IC PLD EEPROM 64 MACROCELL 5NS TQFP44
• Manufacturer: Altera
• Series: MAX 7000Sr

Specifications of EPM7064STC44-5N

• Cpld Type: EEPROM
• No. Of Macrocells: 64
• No. Of I/o's: 68
• Propagation Delay: 5ns
• Global Clock Setup Time: 2.9ns
• Frequency: 175.4MHz
• Supply Voltage Range: 4.75V To 5.25V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

MAX 7000 Programmable Logic Device Family Data Sheet
Notes to tables:
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
48
t
t
t
Symbol
t
t
t
t
t
t
t
t
t
t
Symbol
CLR
PIA
LPA
PD1
PD2
SU
H
FSU
FH
CO1
CH
CL
ASU
Table 34. EPM7160S Internal Timing Parameters (Part 2 of 2)
Table 35. EPM7192S External Timing Parameters (Part 1 of 2)
These values are specified under the recommended operating conditions shown in
information on switching waveforms.
This minimum pulse width for preset and clear applies for both global clear and array controls. The t
must be added to this minimum width if the clear or reset signal incorporates the t
path.
This parameter is a guideline that is sample-tested only and is based on extensive device characterization. This
parameter applies for both global and array clocking.
These parameters are measured with a 16-bit loadable, enabled, up/down counter programmed into each LAB.
The f
Operating conditions: V
For EPM7064S-5, EPM7064S-6, EPM7128S-6, EPM7160S-6, EPM7160S-7, EPM7192S-7, and EPM7256S-7 devices,
these values are specified for a PIA fan-out of one LAB (16 macrocells). For each additional LAB fan-out in these
devices, add an additional 0.1 ns to the PIA timing value.
The t
running in the low-power mode.
LPA
MAX
Input to non-registered output
I/O input to non-registered
output
Global clock setup time
Global clock hold time
Global clock setup time of fast
input
Global clock hold time of fast
input
Global clock to output delay
Global clock high time
Global clock low time
Array clock setup time
Register clear time
PIA delay
Low-power adder
parameter must be added to the t
values represent the highest frequency for pipelined data.
Parameter
Parameter
CCIO
Tables 35
= 3.3 V ± 10% for commercial and industrial use.
(7)
(8)
C1 = 35 pF
C1 = 35 pF
C1 = 35 pF
Conditions
and
Conditions
LAD
36
, t
show the EPM7192S AC operating conditions.
LAC
, t
Min Max Min Max Min Max Min Max
IC
, t
-6
EN
Min
4.1
0.0
3.0
0.0
3.0
3.0
1.0
11.0
, t
2.4
1.6
SEXP
-7
Max
, t
7.5
7.5
4.7
ACL
Note (1)
Note (1)
-7
, and t
Speed Grade
Speed Grade
10.0
Min
7.0
0.0
3.0
0.5
4.0
4.0
2.0
3.0
2.0
CPPW
-10
Table
LAD
Max
10.0
10.0
5.0
parameters for macrocells
-10
parameter into the signal
11.0
14. See
3.0
1.0
Min
11.0
0.0
3.0
0.0
5.0
5.0
4.0
Altera Corporation
Figure 13
-15
-15
Max
LPA
15.0
15.0
8.0
13.0
parameter
4.0
2.0
for more
Unit
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns