S29GL256P10TFI010 Spansion Inc., S29GL256P10TFI010 Datasheet - Page 68

• Manufacturer Part Number: S29GL256P10TFI010
• Description: IC, FLASH, 256MBIT, 100NS, TSOP-56
• Manufacturer: Spansion Inc.

Specifications of S29GL256P10TFI010

• Memory Type: Flash
• Memory Size: 256Mbit
• Memory Configuration: 32M X 8 / 16M X 16
• Ic Interface Type: CFI, Parallel
• Access Time: 100ns
• Supply Voltage Range: 2.7 To 3.6 V
• Memory Case Style: TSOP
• Data Bus Width: 8 bit, 16 bit
• Architecture: Uniform
• Interface Type: Page-mode
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 2.7 V
• Maximum Operating Current: 50 mA
• Mounting Style: SMD/SMT
• Operating Temperature: + 85 C
• Package / Case: TSOP-56
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

68
Read
Reset
CFI Query
Program
Write to Buffer
Program Buffer to Flash (Confirm)
Write-to-Buffer-Abort Reset
Chip Erase
Sector Erase
Erase Suspend/Program Suspend
Erase Resume/Program Resume
Secured Silicon Sector Entry
Secured Silicon Sector Exit
Legend
X = Don’t care
RA = Address of the memory to be read.
RD = Data read from location RA during read operation.
PA = Address of the memory location to be programmed. Addresses latch on
the falling edge of the WE# or CE# pulse, whichever happens later.
Notes
1. See
2. All values are in hexadecimal.
3. All bus cycles are write cycles unless otherwise noted.
4. Data bits DQ15-DQ8 are don’t cares for unlock and command cycles.
5. Address bits A
6. No unlock or command cycles required when reading array data.
7. The Reset command is required to return to reading array data when
8. See
9. The fourth, fifth, and sixth cycles of the autoselect command sequence are
10. The data is 00h for an unprotected sector and 01h for a protected sector.
unless SA or PA required. (A
device is in the autoselect mode, or if DQ5 goes high (while the device is
providing status data).
read cycles.
See
Status Read except that the protect and unprotect statuses are inverted
here.
Manufacturer ID
Device ID
Sector Protect Verify
Secure Device Verify
Enter
Program
Sector Erase
Chip Erase
Reset
(6)
(7)
Table 7.1 on page 19
Table 7.2 on page 22
Autoselect on page 21
(12)
(15)
Command (Notes)
(14)
(8)
(14)
MAX
(14)
:A16 are don’t cares for unlock and command cycles,
(10)
(11)
(18)
(13)
for description of bus operations.
for device ID values and definitions.
for more information. This is same as PPB
MAX
(17)
(16)
is the Highest Address pin.).
Table 12.1 S29GL-P Memory Array Command Definitions, x16
1
1
4
4
4
4
1
4
3
1
3
3
2
2
2
2
6
6
1
1
3
4
Addr
XXX
XXX
XXX
XXX
XXX
XXX
XXX
555
555
555
555
555
555
555
555
555
555
555
555
RA
SA
55
First
S29GL-P MirrorBit
Data
D a t a
RD
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
F0
98
29
A0
80
80
90
B0
30
Addr
2AA
2AA
2AA
2AA
2AA
2AA
2AA
2AA
XXX
XXX
2AA
2AA
2AA
2AA
SA
PA
Second
S h e e t
Data
PD
55
55
55
55
55
55
55
55
30
10
00
55
55
55
55
®
PD = Data to be programmed at location PA. Data latches on the rising edge
of the WE# or CE# pulse, whichever happens first.
SA = Address of the sector to be verified (in autoselect mode) or erased.
Address bits A
WBL = Write Buffer Location. The address must be within the same write
buffer page as PA.
WC = Word Count is the number of write buffer locations to load minus 1.
11. The data value for DQ7 is “1” for a serialized, protected Secured Silicon
12. Command is valid when device is ready to read array data or when device
13. Command sequence returns device to reading array after being placed in
14. The Unlock-Bypass command is required prior to the Unlock-Bypass-
15. The Unlock-Bypass-Reset command is required to return to reading array
16. The system can read and program/program suspend in non-erasing
17. The Erase Resume/Program Resume command is valid only during the
18. The Exit command returns the device to reading the array.
Flash Family
Sector region and “0” for an unserialized, unprotected region. See
Table 7.3 on page 22
is in autoselect mode.
a Write-to-Buffer-Abort state. Full command sequence is required if
resetting out of abort while in Unlock Bypass mode.
Program command.
data when the device is in the unlock bypass mode.
sectors, or enter the autoselect mode, when in the Erase Suspend mode.
The Erase Suspend command is valid only during a sector erase
operation.
Erase Suspend/Program Suspend modes.
Addr
555
555
555
555
555
555
555
555
555
555
555
SA
( P r e l i m i n a r y )
Third
Bus Cycles (Notes 1–5)
max
Data
A0
F0
90
90
90
90
25
20
80
80
88
90
–A16 uniquely select any sector.
[SA]X02
Addr
X00
X01
X03
555
555
for data and definitions.
SA
XX
PA
Fourth
227E
Data
S29GL-P_00_A7 November 8, 2007
(10)
(11)
WC
PD
AA
AA
01
00
Addr
WBL
X0E
2AA
2AA
Fifth
Data
PD
(8)
55
55
Addr
WBL
X0F
555
SA
Sixth
Data
PD
(8)
10
30