S25FL016K0XMFI041 Spansion Inc., S25FL016K0XMFI041 Datasheet - Page 62

• Manufacturer Part Number: S25FL016K0XMFI041
• Description: MEMORY, FLASH, 16M, 3V, SPI, 8SOIC
• Manufacturer: Spansion Inc.

Specifications of S25FL016K0XMFI041

• Memory Size: 16Mbit
• Clock Frequency: 104MHz
• Supply Voltage Range: 2.7V To 3.6V
• Memory Case Style: SO
• No. Of Pins: 8
• Operating Temperature Range: -40°C To +85°C
• Interface: SPI
• Memory Type: RoHS Compliant
• Memory Configuration: 8K X 256 Bytes
• Interface Type: SPI
• Rohs Compliant: Yes

9.
9.1
62
(0.25D x 0.75E)
INDEX AREA
3
PACKAGE
SYMBOL
E1
JEDEC
A
9
A1
A2
E1
b1
c1
L1
L2
θ1
θ2
4
A
D
E
N
Physical Dimensions
b
c
e
L
h
θ
E1/2
A2
SOA008 narrow — 8-pin Plastic Small Outline Package (150-mils Body Width)
A1
0.0531
0.0039
0.0067
0.0067
0.0161
SOA 008 (inches)
0.052
0.012
0.011
MIN
0.10
MS-012(D)AA
0˚
5˚
0.236 BSC
0.1535 BSC
0.193 BSC
.050 BSC
.041 REF
.010 BSC
0˚
8
e
0.0688
0.0098
0.0098
0.061
0.020
0.019
0.009
0.035
0.196
MAX
15˚
8˚
A
B
3
D
1.35
0.10
1.32
0.31
0.27
0.17
0.17
0.41
0.25
4
MIN
0˚
5˚
SOA 008 (mm)
0.25 BSC
1.04 REF
MS-012(D)AA
1.27 BSC
4.90 BSC
6.00 BSC
5
5
3.90 BSC
8
0˚
MAX
1.75
0.25
1.55
0.51
0.48
0.25
0.23
0.89
0.50
15˚
8˚
b
0.10
0.25
C
M
E/2
0.20 C
D a t a
C
A - B
C
D
E
0.10
A - B
D
SEATING PLANE
S25FL016K
S h e e t
C
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
0.33
NOTES:
SEE
DETAIL B
.
ALL DIMENSIONS ARE IN BOTH INCHES AND MILLMETERS.
DIMENSIONING AND TOLERANCING PER ASME Y14.5M - 1994.
DIMENSION D DOES NOT INCLUDE MOLD FLASH,
PROTRUSIONS OR GATE BURRS. MOLD FLASH,
PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.15 mm
PER END. DIMENSION E1 DOES NOT INCLUDE INTERLEAD
FLASH OR PROTRUSION INTERLEAD FLASH OR PROTRUSION
SHALL NOT EXCEED 0.25 mm PER SIDE. D AND E1
DIMENSIONS ARE DETERMINED AT DATUM H.
THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE
BOTTOM. DIMENSIONS D AND E1 ARE DETERMINED AT THE
OUTMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF
MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD
FLASH. BUT INCLUDING ANY MISMATCH BETWEEN THE TOP
AND BOTTOM OF THE PLASTIC BODY.
DATUMS A AND B TO BE DETERMINED AT DATUM H.
"N" IS THE MAXIMUM NUMBER OF TERMINAL POSITIONS FOR
THE SPECIFIED PACKAGE LENGTH.
THE DIMENSIONS APPLY TO THE FLAT SECTION OF THE LEAD
BETWEEN 0.10 TO 0.25 mm FROM THE LEAD TIP.
DIMENSION "b" DOES NOT INCLUDE DAMBAR PROTRUSION.
ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.10 mm TOTAL
IN EXCESS OF THE "b" DIMENSION AT MAXIMUM MATERIAL
CONDITION. THE DAMBAR CANNOT BE LOCATED ON THE
LOWER RADIUS OF THE LEAD FOOT.
THIS CHAMFER FEATURE IS OPTIONAL. IF IT IS NOT PRESENT,
THEN A PIN 1 IDENTIFIER MUST BE LOCATED WITHIN THE INDEX
AREA INDICATED.
LEAD COPLANARITY SHALL BE WITHIN 0.10 mm AS MEASURED
FROM THE SEATING PLANE.
9
C
h
h
C
H
H
( P r e l i m i n a r y )
0
1
DETAIL B
PLATING
METAL
L1
BASE
WITH
L
S25FL016K_00_02 September 8, 2010
A
0
A
c
2
SECTION A-A
0.07 R MIN.
0
(b)
b1
3528 \ 16-038.03 \ 11.02.05
7
L2
SEATING PLANE
GAUGE PLANE
c1