LPC2378FBD144 NXP Semiconductors, LPC2378FBD144 Datasheet - Page 7

• Manufacturer Part Number: LPC2378FBD144
• Description: MCU 32BIT ARM7, 10/100, USB, CAN
• Manufacturer: NXP Semiconductors

Specifications of LPC2378FBD144

• Core Size: 32bit
• No. Of I/o's: 104
• Program Memory Size: 512KB
• Ram Memory Size: 58KB
• Cpu Speed: 72MHz
• Oscillator Type: External, Internal
• No. Of Timers: 4
• No. Of Pwm Channels: 6
• Digital Ic Case: RoHS Compliant
• Controller Family/series: LPC23xx
• Rohs Compliant: Yes

NXP Semiconductors
Table 3.
LPC2377_78
Product data sheet
Symbol
P0[9]/
I2STX_SDA/
MOSI1/MAT2[3]
P0[10]/TXD2/
SDA2/MAT3 [0]
P0[11]/RXD2/
SCL2/MAT3[1]
P0[12]/MISO1/
AD0[6]
P0[13]/
USB_UP_LED2/
MOSI1/AD0[7]
P0[14]/
USB_CONNECT2/
SSEL1
P0[15]/TXD1/
SCK0/SCK
P0[16]/RXD1/
SSEL0/SSEL
P0[17]/CTS1/
MISO0/MISO
Pin description
Pin
109
69
70
29
32
48
89
90
87
[1]
[1]
[2]
[2]
[1]
[1]
[1]
[1]
[1]
…continued
Type
I/O
I/O
I/O
O
I/O
O
I/O
O
I/O
I
I/O
O
I/O
I/O
I
I/O
O
I/O
I
I/O
O
I/O
I/O
O
I/O
I/O
I/O
I
I/O
I/O
I/O
I
I/O
I/O
Description
P0[9] — General purpose digital input/output pin.
I2STX_SDA — Transmit data. It is driven by the transmitter and read by the
receiver. Corresponds to the signal SD in the I
MOSI1 — Master Out Slave In for SSP1.
MAT2[3] — Match output for Timer 2, channel 3.
P0[10] — General purpose digital input/output pin.
TXD2 — Transmitter output for UART2.
SDA2 — I
MAT3[0] — Match output for Timer 3, channel 0.
P0[11] — General purpose digital input/output pin.
RXD2 — Receiver input for UART2.
SCL2 — I
MAT3[1] — Match output for Timer 3, channel 1.
P0[12] — General purpose digital input/output pin.
MISO1 — Master In Slave Out for SSP1.
AD0[6] — A/D converter 0, input 6.
P0[13] — General purpose digital input/output pin.
USB_UP_LED2 — USB2 Good Link LED indicator. It is LOW when device is
configured (non-control endpoints enabled). It is HIGH when the device is not
configured or during global suspend. (LPC2378 only)
MOSI1 — Master Out Slave In for SSP1.
AD0[7] — A/D converter 0, input 7.
P0[14] — General purpose digital input/output pin.
USB_CONNECT2 — USB2 Soft Connect control. Signal used to switch an external
1.5 kΩ resistor under software control. Used with the SoftConnect USB feature.
(LPC2378 only)
SSEL1 — Slave Select for SSP1.
P0[15] — General purpose digital input/output pin.
TXD1 — Transmitter output for UART1.
SCK0 — Serial clock for SSP0.
SCK — Serial clock for SPI.
P0 [16] — General purpose digital input/output pin.
RXD1 — Receiver input for UART1.
SSEL0 — Slave Select for SSP0.
SSEL — Slave Select for SPI.
P0[17] — General purpose digital input/output pin.
CTS1 — Clear to Send input for UART1.
MISO0 — Master In Slave Out for SSP0.
MISO — Master In Slave Out for SPI.
All information provided in this document is subject to legal disclaimers.
2
2
C2 clock input/output (this is not an open-drain pin).
C2 data input/output (this is not an open-drain pin).
Rev. 5 — 17 June 2010
Single-chip 16-bit/32-bit microcontrollers
2
S-bus specification.
LPC2377/78
© NXP B.V. 2010. All rights reserved.
7 of 68