OP470GS Analog Devices Inc, OP470GS Datasheet - Page 9

• Manufacturer Part Number: OP470GS
• Description: Operational Amplifier (Op-Amp) IC
• Manufacturer: Analog Devices Inc
• Type: General Purpose Amplifierr

Specifications of OP470GS

• No. Of Amplifiers: 4
• Bandwidth: 6MHz
• Slew Rate: 2V/µs
• No. Of Pins: 16
• Operating Temperature Range: -40°C To +85°C
• Peak Reflow Compatible (260 C): No
• Leaded Process Compatible: No
• Rohs Status: RoHS non-compliant
• Amplifier Type: General Purpose
• Number Of Circuits: 4
• Gain Bandwidth Product: 6MHz
• Current - Input Bias: 25nA
• Voltage - Input Offset: 400µV
• Current - Supply: 9mA
• Voltage - Supply, Single/dual (±): 9 V ~ 36 V, ±4.5 V ~ 18 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 16-SOIC (0.300", 7.5mm Width)
• Rail/rail I/o Type: No
• Number Of Elements: 4
• Unity Gain Bandwidth Product: 6MHz
• Common Mode Rejection Ratio: 100dB
• Input Offset Voltage: 1mV
• Input Bias Current: 60nA
• Single Supply Voltage (typ): Not RequiredV
• Dual Supply Voltage (typ): ±5/±9/±12/±15V
• Voltage Gain In Db: 124.61dB
• Power Supply Rejection Ratio: 120dB
• Power Supply Requirement: Dual
• Shut Down Feature: No
• Single Supply Voltage (min): Not RequiredV
• Single Supply Voltage (max): Not RequiredV
• Dual Supply Voltage (min): ±4.5V
• Dual Supply Voltage (max): ±18V
• Technology: Bipolar
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 16
• Package Type: SOIC W
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Output Type: -
• Current - Output / Channel: -
• -3db Bandwidth: -
• Lead Free Status / Rohs Status: Not Compliant

APPLICATIONS INFORMATION
Voltage and Current Noise
The OP470 is a very low-noise quad op amp, exhibiting a typi-
cal voltage noise of only 3.2 nV÷Hz @ 1 kHz. The exceptionally
low-noise characteristics of the OP470 are in part achieved by
operating the input transistors at high collector currents since
the voltage noise is inversely proportional to the square root of
the collector current. Current noise, however, is directly propor-
tional to the square root of the collector current. As a result, the
outstanding voltage noise performance of the OP470 is gained
at the expense of current noise performance, which is typical for
low noise amplifiers.
To obtain the best noise performance in a circuit, it is vital to
understand the relationship between voltage noise (e
noise (i
TOTAL NOISE AND SOURCE RESISTANCE
The total noise of an op amp can be calculated by:
where:
REV. B
n
+1V
–1V
), and resistor noise (e
E
e
i
e
R
Figure 2. Channel Separation Test Circuit
E
n
n
t
n
S
= op amp current noise
= source resistance thermal noise
n
= up amp voltage noise
= total input referred noise
= source resistance
=
500
50
( )
e
10
CHANNEL SEPARATION = 20 LOG
Figure 3. Burn-In Circuit
9
2
3
n
2
–18V
+18V
A
C
+
4
11
(
1/4
OP470
1/4
OP470
i R
n
50k
8
1
5k
S
t
)
).
2
+1V
–1V
+
( )
e
t
2
V
V
1
2
20V p-p
13
12
6
5
V
2
/1000
V
1
D
B
n
14
7
), current
–9–
The total noise is referred to the input and at the output would
be amplified by the circuit gain. Figure 4 shows the relationship
between total noise at 1 kHz and source resistance. For R
the total noise is dominated by the voltage noise of the OP470.
As R
by resistor noise rather than by voltage or current noise of the
OP470. When R
becomes the major contributor to total noise.
Figure 5 also shows the relationship between total noise and
source resistance, but at 10 Hz. Total noise increases more
quickly than shown in Figure 4 because current noise is inversely
proportional to the square root of frequency. In Figure 5, current
noise of the OP470 dominates the total noise when R
From Figures 4 and 5 it can be seen that to reduce total noise,
source resistance must be kept to a minimum. In applications
with a high source resistance, the OP400, with lower current
noise than the OP470, will provide lower total noise.
Figure 4. Total Noise vs. Source Resistance (Including
Resistor Noise) at 1 kHz
Figure 5. Total Noise vs. Source Resistance (Including
Resistor Noise) at 10 Hz
S
rises above 1 kW, total noise increases and is dominated
100
100
10
10
1
1
100
100
OP470
OP400
OP470
OP400
OP471
OP471
OP11
OP11
S
exceeds 20 kW, current noise of the OP470
RESISTOR
NOISE ONLY
RESISTOR
NOISE ONLY
R
R
S
S
– SOURCE RESISTANCE –
– SOURCE RESISTANCE –
1k
1k
10k
10k
OP470
S
> 5 kW.
S
100k
100k
< 1 kW