C25BNF230B EATON CUTLER HAMMER, C25BNF230B Datasheet - Page 18

• Manufacturer Part Number: C25BNF230B
• Description: Definite Purpose Contactor
• Manufacturer: EATON CUTLER HAMMER

Specifications of C25BNF230B

• Load Current Inductive: 30A
• Load Current Resistive: 40A
• No. Of Poles: 2
• Contact Configuration: DPST-NO
• Relay Mounting: Panel
• Coil Voltage Vac Nom: 240V
• Contact Voltage Ac Nom: 600V
• Horsepower: 5hp

35
35-18
Overload Relays
These tripping characteristics are the
mean values of the spread at 20°C
ambient temperature in a cold state.
Table 35-49. Overload Relay — Technical Data and Specifications
General
Description
Standards
Climatic Proofing
Ambient Temperature
Temperature Compensation
Mechanical Shock Resistance (IEC/EN 60068-2-27)
Degree of Protection
Protection against Direct Contact when Actuated
from Front (IEC 536)
Insulation Voltage (U i ) VAC
Overvoltage Category /Pollution Degree
Impulse Withstand Voltage (U imp ) VAC
Operational Voltage (U e ) VAC
Safe Isolation to VDE 0106 Part 101 and Part 101/A1
Overload Relay Setting Range
Temperature Compensation Residual Error >20°C (%/K)
Current Heat Loss (3 Conductors)
Terminal Capacity
Solid or Stranded, AWG
Terminal Screw
Tools
Half-sinusoidal Shock 10 mS
Between auxiliary contacts and main contacts (VAC)
Between main contacts (VAC)
Lower value of setting range, W
Upper value of setting range, W
Solid, mm
Flexible with ferrule, mm
Tightening Torque
Pozidrive screwdriver
Standard screwdriver
Ambient temperature operating range to IEC/EN 60947, PTB: -5°C to +50°C.
6 mm
Main contact terminal capacity, solid and stranded conductors with ferrules: When using 2 conductors use identical cross-section.
Nm
Lb-in
Definite Purpose Contactors & Starters
Starters
Overload Relay Specifications
2
flexible with ferrules to DIN 46228.
2
2
Tripping time depends on response
current. With devices at operating tem-
perature, the tripping time of the over-
load relay reduces to approximately
25% of the read off value. Specific
characteristics for each individual
setting range can be found in
MN03402001E.
For more information visit: www.eaton.com
XTOB…CC1
IEC/EN 60947, VDE 0660, UL, CSA
Damp heat, constant, to IEC 60068-2-78;
Damp heat, cyclic, to IEC 60 068-2-30
-25 to 50°C [-13 to 122°F]
Continuous
10g
IP20
Finger and back of hand proof
690
III/3
6000
690
440
440
0.1 – 32A
2.5
6
2 x (1 – 6)
2 x (1 – 4)
2 x (1 – 6)
14-8
M4
1.8
16
Size 2
1 x 6
0.25
Figure 35-8. Tripping Characteristics
XTOB…DC1
IEC/EN 60947, VDE 0660, UL, CSA
Damp heat, constant, to IEC 60068-2-78;
Damp heat, cyclic, to IEC 60 068-2-30
-25 to 50°C [-13 to 122°F]
Continuous
10g
IP20
Finger and back of hand proof
690
III/3
6000
690
440
440
6 – 75A
3
7.5
2 x (1 – 16)
1 x 25
2 x (1 – 10)
14-2
M6
3.5
31
Size 2
1 x 6
0.25
100
0.6
2h
60
40
20
10
40
20
10
6
4
2
1
6
4
2
1
1 1.5 2
2-Phase
3 4
XTOB...CC1,
XTOB...DC1
6 8 10 15 20
3-Phase
CA08102001E
October 2008