APDS-9004-020 Avago Technologies US Inc., APDS-9004-020 Datasheet
APDS-9004-020
Specifications of APDS-9004-020
APDS-9004-021
Related parts for APDS-9004-020
APDS-9004-020 Summary of contents
Page 1
... Figure suitable for portable applications with its ultra small package design. The APDS-9004 is ideal for applications in which the measurement of ambient light is used to control display backlighting. Mobile appliances such as the mobile phones and PDAs that draw heavy current from ...
Page 2
... APDS- 9004 ambient light photo sensor module. You can contact them through your local sales representatives for additional details. Ordering Information Part Number Packaging Type APDS-9004-020 Tape and Reel Typical Application Circuit Pin 3:V Pin 2:V CC APDS -9004 Pin 4:NC Figure 1 ...
Page 3
Absolute Maximum Ratings For implementations where case to ambient thermal resistance is ≤ 50 °C /W Parameter Storage Temperature Operating Temperature Supply Voltage Recommended Operating Conditions Parameter Symbol Supply Voltage V Electrical & Optical Specifications (Ta=25° ° ° ° ° ...
Page 4
... APDS-9004 Performance Charts Average Iout Vs Lux (Vcc=3V,T=25C) 10000 White LED 1000 100 100 Lux Relative Output current Vs Vcc ( T=25C, 100 Lux) 1.10 1.08 Relative Iout 1.06 1.04 1.02 1.00 0.98 0.96 2 2.5 3 3.5 4 Vcc(V) 4 Relative Output Current Vs Temperature (Vcc=3V, 100 Lux) 2 ...
Page 5
... APDS-9004 Light Measurement Circuit and Waveforms I_pulse Pin 2:V Pin 3:V CC APDS-9004 Pin 4:NC sensor-output attains ~95% of its voltage magnitude corresponds to the set light level VCC Pulse from PG Sensor Output at load Tset 5 I_pulse I_pulse CC Pin 1:OUT VOUT VOUT GND GND R LOAD ...
Page 6
... APDS-9004 Package Outline 6 ...
Page 7
... APDS-9004 Tape and Reel Dimensions 7 ...
Page 8
... Moisture Proof Packaging Chart All APDS-9004 options are shipped in moisture proof package. Once opened, moisture absorption begins. This part is compliant to JEDEC Level 3. Baking conditions If the parts are not stored in dry conditions, they must be baked before reflow to prevent damage to the parts. Package Temp ...
Page 9
... The temperatures are measured at the component to printed circuit board connections. In process zone P1, the PC board and APDS-9004 pins are heated to a temperature of 150°C to activate the flux in the solder paste. The temperature ramp up rate, R1, is limited to 3°C per second to allow for even heating of both the PC board and APDS-9004 pins ...
Page 10
... Reverse Side of the PCBA 0.60 Figure 2. Recommended Land Pattern 10 Metal Stencil For Solder Paste Printing Land Pattern Slot Opening for APDS- 9004 to be exposed on the Reverse Side of the PCBA Soldering Terminal C L 0.71 1.89 0.71 0.50 0.60 Unit: mm 2.00 Tolerance: +/- 0 ...
Page 11
Recommended Metal Solder Stencil Aperture It is recommended that a 0.11 mm (0.004 inches) thick stencil be used for solder paste printing. Aperture opening for shield pad is 0.6mm x 0.71mm. This is to ensure adequate printed solder paste ...
Page 12
... Appendix B: Optical Window Design for APDS-9004 Optical Window Dimensions To ensure that the performance of the APDS-9004 will not be affected by improper window design, there are some constraints on the dimensions and design of the window. There is a constraint on the minimum size of the window, which is placed in front of the photo light sensor, so that it will not affect the angular response of the APDS-9004 ...
Page 13
... Table 1 and Figure 6 below show the recommended dimensions of the window. These dimension values are based on a window thickness of 1.0mm with a refractive index 1.585. WD: Working Distance between window front panel & APDS-9004 D1: Window Diameter T: Thickness L: Length of Light Pipe D2: Light Pipe Diameter Z: Distance between window rear panel and APDS-9004 ...
Page 14
... Light Source APDS-9004 4 Figure 7. Configuration of APDS-9004 being used directly Selection of the load resistor RL will determine the amount of current-to-voltage conversion in the circuit. Light source e.g. fluorescent light consists of ac noise about 100Hz frequency. A capacitor of 10uF, which acting as a low-pass filter, is recommended to add in parallel with the load resistor to by-pass this ripples ...