SPC5604PEF0MLQ6 Freescale Semiconductor, SPC5604PEF0MLQ6 Datasheet - Page 64

• Manufacturer Part Number: SPC5604PEF0MLQ6
• Description: IC MCU 32BIT 512KB FLASH 144LQFP
• Manufacturer: Freescale Semiconductor
• Series: MPC56xx Qorivvar

Specifications of SPC5604PEF0MLQ6

• Core Processor: e200z0h
• Core Size: 32-Bit
• Speed: 64MHz
• Connectivity: CAN, FlexRay, LIN, SPI, UART/USART
• Peripherals: DMA, POR, PWM, WDT
• Number Of I /o: 108
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 64K x 8
• Ram Size: 40K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 30x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 144-LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

3.13
3.14
The device provides a 10-bit successive approximation register (SAR) analog-to-digital converter.
64
4
5
6
7
8
9
10
11
12
13
14
1



Symbol
Self-clocked mode frequency is the frequency that the PLL operates at when the reference frequency falls outside
the f
f
enhanced mode.
This value is determined by the crystal manufacturer and board design.
Jitter is the average deviation from the programmed frequency measured over the specified interval at maximum
f
signal. Noise injected into the PLL circuitry via V
increase the C
Proper PC board layout procedures must be followed to achieve specifications.
Values are with frequency modulation disabled. If frequency modulation is enabled, jitter is the sum of C
either f
Short term jitter is measured on the clock rising edge at cycle n and cycle n+4.
This value is determined by the crystal manufacturer and board design. For 4 MHz to 20 MHz crystals specified for
this PLL, load capacitors should not exceed these limits.
This specification applies to the period required for the PLL to relock after changing the MFD frequency control bits
in the synthesizer control register (SYNCR).
This value is true when operating at frequencies above 60 MHz, otherwise f
Modulation depth will be attenuated from depth setting when operating at modulation frequencies above 50 kHz.
RCMSTEP
PTF = Post Trimming Frequency: The frequency of the output clock after trimming at typical supply voltage and
temperature
RCMTRIM
VCO
SYS
RCMVAR
f
RC
16 MHz RC oscillator electrical characteristics
Analog-to-digital converter (ADC) electrical characteristics
. Measurements are made with the device powered by filtered supplies and clocked by a stable external clock
LOR
self clock range is 20–150 MHz. f
CS
window.
or f
C
P RC oscillator frequency
P Fast internal RC oscillator variation over temperature and
T Post Trim Accuracy: The variation of the PTF
T Fast internal RC oscillator trimming step
supply with respect to f
configuration
16 MHz
DS
JITTER
(depending on whether center spread or down spread modulation is enabled).
percentage for a given interval.
Table 29. 16 MHz RC oscillator electrical characteristics
MPC5604P Microcontroller Data Sheet, Rev. 7
RC
Parameter
SCM
at T
A
represents f
= 25 °C in high-frequency
DDPLL
and V
SYS
1
from the
after PLL output divider (ERFD) of 2 through 16 in
SSPLL
and variation in crystal oscillator frequency
Conditions
T
T
T
A
A
A
CS
= 25 °C
= 25 °C
= 25 °C
—
is 2% (above 64 MHz).
Min
–5
–1
—
—
Value
Freescale Semiconductor
Typ
1.6
16
—
—
Max
—
—
JITTER
5
1
Unit
MHz
and
%
%
%