SPC5604PEF0MLQ6 Freescale Semiconductor, SPC5604PEF0MLQ6 Datasheet - Page 70

• Manufacturer Part Number: SPC5604PEF0MLQ6
• Description: IC MCU 32BIT 512KB FLASH 144LQFP
• Manufacturer: Freescale Semiconductor
• Series: MPC56xx Qorivvar

Specifications of SPC5604PEF0MLQ6

• Core Processor: e200z0h
• Core Size: 32-Bit
• Speed: 64MHz
• Connectivity: CAN, FlexRay, LIN, SPI, UART/USART
• Peripherals: DMA, POR, PWM, WDT
• Number Of I /o: 108
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 64K x 8
• Ram Size: 40K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 30x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 144-LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

3.15
70
1
2
3
4
5
6
7
1
2
3
4
5
T
TUE
TUE
V
from V
AD_clk clock is always half of the ADC module input clock defined via the auxiliary clock divider for the ADC.
When configured to allow 60 MHz ADC, the minimum ADC clock speed is 9 MHz, below which precision is lost.
During the sample time the input capacitance CS can be charged/discharged by the external source. The internal
resistance of the analog source must allow the capacitance to reach its final voltage level within t
end of the sample time t
for the sample clock t
This parameter includes the sample time t
20 MHz ADC clock. Specific prescaler is programmed on MC_PLL_CLK to provide 20 MHz clock to the ADC.
See
Typical program and erase times assume nominal supply values and operation at 25 °C. All times are subject to
change pending device characterization.
Initial factory condition: < 100 program/erase cycles, 25 °C, typical supply voltage.
The maximum program and erase times occur after the specified number of program/erase cycles. These maximum
values are characterized but not guaranteed.
Actual hardware programming times. This does not include software overhead.
Typical Bank programming time assumes that all cells are programmed in a single pulse. In reality some cells will
require more than one pulse, adding a small overhead to total bank programming time (see Initial Max column).
T
T
Symbol
T
GE
128kpperase
Symbol
DD
16kpperase
32kpperase
dwprogram
T
BKPRG
Flash memory electrical characteristics
Figure
= 3.3 V to 3.6 V / 4.5 V to 5.5 V, T
SS_HV_ADCx
CC T Gain error
CC P Total unadjusted error without current
CC T Total unadjusted error with current
15.
C
C
P Double Word (64 bits) Program Time
P Bank Program (512 KB)
P Bank Program (64 KB)
P 16 KB Block Pre-program and Erase Time
P 32 KB Block Pre-program and Erase Time
P 128 KB Block Pre-program and Erase Time
injection
injection
to V
ADC_S
DD_HV_ADCx
Table 30. ADC conversion characteristics (continued)
ADC_S
depend on programming.
Parameter
Table 31. Program and erase specifications
, changes of the analog input voltage have no effect on the conversion result. Values
MPC5604P Microcontroller Data Sheet, Rev. 7
Parameter
.
A
= –40 °C to T
4, 5
ADC_S
4, 5
.
A MAX
4
, unless otherwise specified and analog input voltage
Conditions
Min
—
—
—
—
—
—
—
—
—
1
Typical
1.45
0.18
300
400
800
22
Value
1
–2.5
Min
—
–3
Initial
max
1300
1.65
0.21
500
600
50
Value
Freescale Semiconductor
2
Typ
±1
—
—
ADC_S
Max
5000
5000
7500
4.10
500
33
Max
2.5
—
. After the
3
3
Unit
Unit
LSB
LSB
LSB
ms
ms
ms
µs
s
s