QS30LLP BANNER ENGINEERING, QS30LLP Datasheet
QS30LLP
Specifications of QS30LLP
Related parts for QS30LLP
QS30LLP Summary of contents
Page 1
... Visible Red, Class 1 laser; 650 nm Excess Gain With Supplied Target With Supplied Target BRT-36X40BM BRT-TVHG-2X2 1000 1000 with BRT-36X40BM 100 100 0 100 m 0.1 m 1.0 m 0.33' 3.3' 33' 330' 0.33' 3.3' DISTANCE DISTANCE QS30LLP W/30 ). P/N 112355 rev. A with BRT-TVHG2X2 10 m 100 m 33' 330' ...
Page 2
... The sensor can be side-mounted, using integral mounting holes, or front-mounted, via the 30 mm threaded barrel. Model QS30LLP(Q) is configured using the Maximum Excess Gain SET procedure useful for long-range applications and high variations in contrast, such as beam-break applications where the target objects are larger than the beam ...
Page 3
... Disabling the push buttons prevents undesired tampering with the programming settings. Connect the gray wire of the sensor as described on above, and four-pulse to either enable or disable the push buttons: Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 ...
Page 4
... WORLD-BEAM QS30 Series – ® Maximum Excess Gain SET – Model QS30LLP • Sets the sensor for maximum excess gain without allowing false proxing. Provides maximum contrast between any reflector and a blocked condition and is stable even in dirty environments. • Useful for long-range applications and high variations in contrast, such as beam- break applications where the target objects are larger than the beam ...
Page 5
... Tel: 763.544.3164 QS30 Series – Polarized Retroreflective Laser Sensors Low-Contrast SET – Model QS30LLPC • Sets a switchpoint at 35 percent below the signal from the retroreflector. • Useful for small object detection and other applications with small variations in contrast, such as yarn- or thread-break applications. ...
Page 6
... Press and hold both push buttons > 2 seconds 6 P/N 112355 rev. A Polarized Retroreflective Laser Sensors — — • Green Power LED turns OFF — + — — + — DO, No Delay DO Delay + — • Green Power LED turns ON + — Banner Engineering Corp SETUP 3 3 Status Indicators Figure 5 ...
Page 7
... Excess Gain SET. This sensor is typically recommended for long-range applications of relatively small targets that will completely break the beam. Smaller objects can be detected by using model QS30LLPC(Q), adjusting the sensor gain down using the Manual Adjust, or performing a Low-Contrast SET of the reflector. Objects as small as 2.0 mm can be reliably detected after performing the Low-Contrast SET at ranges (18') ...
Page 8
... Polarized Retroreflective Laser Sensors Specifications : Flashes Red when delay is selected LED 2 (DO): Flashes Red when Dark Operate is selected LED 1 (LO): Flashes Red when Light Operate is selected Model QS30LLP Model QS30LLPC LED 8: >6X LED 8: >2X LED 7: 5-6X LED 7: 1.5-2X LED 6: 4-5X LED 6: 1-1.5X LED 5: 3-4X LED 5: 0 ...
Page 9
... Load bk Load gy Remote Teach Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 Polarized Retroreflective Laser Sensors Description of Laser Class Class 1 Lasers that are safe under reasonably foreseeable conditions of operation, including the use of optical instruments for intrabeam viewing. ...
Page 10
... Slot (2) (0.16" x 0.56") Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 White Wire Blue Wire Gray Wire with BRT-2X2 1 100 m 3 330 ft DISTANCE 8.9 mm (0.40") Clear 61 mm (2.4") ...
Page 11
... Other compatible mounting bracket (see Banner Photoelectric catalog or website for more information): • SMB30MM • SMB30A Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 Polarized Retroreflective Laser Sensors Accessory Brackets SMBQS30LT 4.5 mm (0.18") 24.0 mm (0.95" ...
Page 12
... This warranty does not cover damage or liability for the improper application of Banner products. This warranty is in lieu of any other warranty either expressed or implied. P/N 112355 rev. A Banner Engineering Corp., 9714 Tenth Ave. No., Minneapolis, MN USA 55441 • Phone: 763.544.3164 • www.bannerengineering.com • Email: sensors@bannerengineering.com Polarized Retroreflective Laser Sensors ...