QS18EP6D BANNER ENGINEERING, QS18EP6D Datasheet - Page 5

• Manufacturer Part Number: QS18EP6D
• Description: Photoelectric Sensor
• Manufacturer: BANNER ENGINEERING

Specifications of QS18EP6D

• Output Current: 100mA
• Sensor Output: PNP
• Supply Voltage Range Dc: 10V To 30V
• Sensor Housing: Rectangular
• Sensor Input: Optical
• Body Material: ABS
• Supply Voltage Max: 30VDC
• Sensing Range Max: 800mm
• Contact Current Max: 35mA
• Sensing Mode: Diffuse
• Sensor Body Material: ABS

Figure 7. Window SET (Light Operate shown)
Access SETUP functions directly from RUN mode, using the procedures detailed below.
30 ms OFF-Delay (Pulse Stretcher) Enable/Disable
Light-Operate/Dark-Operate Select
* Initial Output LED condition is simultaneous with Power LED 3-flash.
(no signal)
(no signal)
(no signal)
(no signal)
Darkest
Darkest
Darkest
threshold ≈12.5% above
the presented condition
Output OFF
Banner Engineering Corp. • Minneapolis, MN U.S.A.
Sensor positions
www.bannerengineering.com • Tel: [phone]
Output OFF
Output OFF
• F rom RUN mode, seven-click
• P ress and hold push button
• Present sensing condition.
• Double-click push button.
• F rom RUN mode, six-click the
0.04 seconds ≤ “Click” ≤ 0.8 seconds
0.04 seconds ≤ “Click” ≤ 0.8 seconds
0.04 seconds ≤ “Click” ≤ 0.8 seconds
the push button.
2 – 4 seconds.
push button.
Presented
Condition
Single
Presented
Condition
T
T
T
T
Output
Push Button
Single
T
T
ON
Push Button
Push Button
> 2 seconds
12.5%
> 2 seconds
Single
Presented
Condition
T
T
T
Sensor positions
threshold ≈12.5% below
the presented condition
> 2 seconds
Output ON
Output ON
Sensor positions
window thresholds
≈12.5% from the
presented condition
T
T
Output OFF
6
T
Most Light
Most Light
Most Light
(saturated
(saturated
(saturated
(saturated
7
T T T
T
T T T
T
signal)
signal)
signal)
signal)
T
T
2
T
T
T
T
T T T
T
T
T
T
T
T
T
T
T
• F rom RUN mode, seven-pulse
T
T
T
• Single-pulse remote line.
• P resent sensing condition.
• Double-pulse remote line.
• F rom RUN mode, six-pulse
T
T
remote line.
T
T
remote line.
T
T
T
0.04 seconds ≤ T ≤ 0.8 seconds
T
0.04 seconds ≤ T ≤ 0.8 seconds
0.04 seconds ≤ T ≤ 0.8 seconds
• S ingle ON condition window extends approximately 12.5% above and below the presented
• Lighter or darker conditions (“outside” the window) cause the output to change state.
• R ecommended for applications where the target to be sensed may not always appear in the
T
T
T
T
T
condition when Light Operate is selected (see Figure 7). Output ON and OFF conditions can be
reversed by changing the Light-/Dark-Operate setting (see below).
same place, or when other unwanted signals may appear.
T
T
T
T
T
T
T
T
T
T
T
Remote Line
T
T
T
T
T
T
T
Remote Line
Remote Line
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
Single-point Light SET (LO)
T
Window Set (LO)
T
T
T
T
T
T
T
T
T
T
T
T
Dark SET (LO)
T
T
T
> 2 seconds
T
Sensor SETUP
T
T
T
T
T
0.8 seconds
T
T
T
T
T
T
T
0.8 seconds
T
T
T
0.8 seconds
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
Sensor toggles between Light-/Dark-Operate settings and returns to RUN
mode.
Power LED: Flashes 3x, then ON Green
Output LED: L ight Operate – ON,*
WORLD-BEAM
Sensor waits for sensing condition.
Power LED: OFF
Output LED: Slow flash (1 Hz)
Sensor toggles between enable/disable settings and returns to RUN
mode.
Power LED: Flashes 3x, then ON Green
Output LED: E nabled – ON,*
T T T
T
T
T
T
T
T
Power LED: Flashes 3x, then ON Green
Output LED: OFF,* then ON or OFF, depending on output state
Sensor returns to RUN mode with new settings.
Power LED: OFF
Output LED: Slow flash (1 Hz)
Sensor returns to wait state, ready for sensing condition.
T
T
Push Button
Window SET
T
T
Dark Operate – OFF,*
Then ON or OFF, depending on output state
Disabled – OFF,*
Then ON or OFF, depending on output state
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
Result
T
T
T
Result
Result
0.8 seconds
T
T
T
®
Power LED: OFF
Output LED: Double-flash
T
T
T
QS18E Series
T
T
T
T
T
T
Remote Line
P/N 136564 rev. A
5