Photoelectric Sensor

QS30LLPQ

Manufacturer Part NumberQS30LLPQ
DescriptionPhotoelectric Sensor
ManufacturerBANNER ENGINEERING
QS30LLPQ datasheet
 


Specifications of QS30LLPQ

Sensing Range0.2m To 18mOutput Current150mA
Sensor OutputNPN/PNPSupply Voltage Range Dc10V To 30V
Sensor HousingRectangularSensing Range Min0.2m
Sensor InputLaserBody MaterialABS Plastic
1
Page 1
2
Page 2
3
Page 3
4
Page 4
5
Page 5
6
Page 6
7
Page 7
8
Page 8
9
Page 9
10
Page 10
11
12
Page 1/12

Download datasheet (804Kb)Embed
Next
Excellent for applications where high sensing power and small beam size are important. Operates over
sensing ranges typically accomplished only by conventional opposed-mode photoelectrics; uses a special
filter to polarize the emitted light, filtering out unwanted reflections from shiny objects.
Spot
Range and
Model
Size at
Use
Focus
0.2 to 18 m
QS30LLP
(0.67' to 60')
Maximum
Excess Gain
SET for
QS30LLPQ
Approx.
Long-Range
4 mm
Applications
at 10 m
(0.16"
0.2 to 18 m
QS30LLPC
at 33')
(0.67' to 60')
Low-Contrast
SET for
Small Object
QS30LLPCQ
Detection
*9 m (30') cables are available by adding suffix “
A model with a QD connector requires a mating cable (see page 10).
!
WARNING . . .
Not To Be Used for Personnel Protection
Never use this product as a sensing device for personnel protection. Doing so could lead to serious injury or death.
This product does NOT include the self-checking redundant circuitry necessary to allow its use in personnel safety applications.
A sensor failure or malfunction can cause either an energized or de-energized sensor output condition. Consult your current Banner Safety
Products catalog for safety products which meet OSHA, ANSI and IEC standards for personnel protection.
Printed in USA
®
WORLD-BEAM
QS30 Series
Polarized Retroreflective Laser Sensors
• Visible class 1 laser with small, effective beam size
• Excellent optical performance throughout sensing range, even close up
• Easy push-button SET options: Maximum Excess Gain or Low-Contrast SET,
depending on model, plus Manual Adjust
• Easy-to-read operating status indicators, with 8-segment bargraph display
• Bipolar discrete outputs, PNP and NPN
• Selectable 30 millisecond OFF-delay
• Models available with 2 m or 9 m (6.5' or 30') cable or integral quick-disconnect
• Tough ABS housing rated IEC IP67; NEMA 6
• Compact housing, mounting versatility – popular 30 mm threaded nose or
side-mount
Models
Output
Cable*
Supply
Type
2 m (6.5')
5-wire Cable
Integral
5-pin
Euro-style
QD
10 to
Bipolar
30V dc
NPN/PNP
2 m (6.5')
5-wire Cable
Integral
5-pin
Euro-style
QD
W/30
” to the model number of any cabled sensor (e.g.,
09/04
Features
P
Visible Red, Class 1 laser; 650 nm
Excess Gain
With Supplied Target
With Supplied Target
BRT-36X40BM
BRT-TVHG-2X2
1000
1000
with BRT-36X40BM
E
E
X
X
C
C
100
100
E
E
S
S
S
S
G
10
G
10
A
A
I
I
N
N
1
1
0.1 m
1.0 m
10 m
100 m
0.1 m
1.0 m
0.33'
3.3'
33'
330'
0.33'
3.3'
DISTANCE
DISTANCE
QS30LLP W/30
).
P/N 112355 rev. A
with BRT-TVHG2X2
10 m
100 m
33'
330'

QS30LLPQ Summary of contents

  • Page 1

    ... Spot Range and Model Size at Use Focus 0 QS30LLP (0.67' to 60') Maximum Excess Gain SET for QS30LLPQ Approx. Long-Range 4 mm Applications (0.16" 0 QS30LLPC at 33') (0.67' to 60') Low-Contrast SET for Small Object ...

  • Page 2

    ... Light Operate Figure 1. Model QS30LLP features Bar Graph Switching Threshold SETUP Status Indicators: Delay Dark Operate Light Operate Figure 2. Model QS30LLPC features Banner Engineering Corp. www.bannerengineering.com • Tel: 763.544.3164 Yellow Output Green Power ON Conducting Indicator Indicator Configuration Push Buttons Yellow Output ...

  • Page 3

    ... Disabling the push buttons prevents undesired tampering with the programming settings. Connect the gray wire of the sensor as described on above, and four-pulse to either enable or disable the push buttons: Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 ...

  • Page 4

    ... Green Power LED: OFF Yellow Output LED: ON Bargraph: #7 & 8 flashing • Sensor returns to RUN mode T with new settings • Use Manual Adjust to increase or T decrease sensor excess gain Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 Most Light (saturated signal) — + GAIN ...

  • Page 5

    ... Figure 4. Low-contrast SET (Dark Operate shown) or Push Buttons • Align sensor to reflector • Press and hold “+” > 2 seconds Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 QS30 Series – Polarized Retroreflective Laser Sensors Low-Contrast SET – Model QS30LLPC • ...

  • Page 6

    ... Press and hold both push buttons > 2 seconds 6 P/N 112355 rev. A Polarized Retroreflective Laser Sensors — — • Green Power LED turns OFF — + — — + — DO, No Delay DO Delay + — • Green Power LED turns ON + — Banner Engineering Corp SETUP 3 3 Status Indicators Figure 5 ...

  • Page 7

    ... Never stare directly into the sensor lens. Laser light can damage your eyes. Avoid placing any mirror-like object in the beam. Never use a mirror as a retroreflective target. Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 QS30 Series – Polarized Retroreflective Laser Sensors Conventional retroreflective photoelectric sensors are extremely easy to align. Beam angles are wide, and retro targets are forgiving to the light beam’ ...

  • Page 8

    ... LED 5: 3-4X LED 5: 0.8X LED 4: 2-3X LED 4: 0.6X LED 3: 1-2X LED 3: 0.4X LED 2: 0.5-1X LED 2: 0.2X LED 1: 0-0.5X LED 1: 0X Banner Engineering Corp. www.bannerengineering.com • Tel: 763.544.3164 Factory Defaults: • No Delay • Dark Operate • Push buttons enabled Minneapolis, MN U.S.A. • ...

  • Page 9

    ... Load bk Load gy Remote Teach Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 Polarized Retroreflective Laser Sensors Description of Laser Class Class 1 Lasers that are safe under reasonably foreseeable conditions of operation, including the use of optical instruments for intrabeam viewing. ...

  • Page 10

    ... Slot (2) (0.16" x 0.56") Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 White Wire Blue Wire Gray Wire with BRT-2X2 1 100 m 3 330 ft DISTANCE 8.9 mm (0.40") Clear 61 mm (2.4") ...

  • Page 11

    ... Other compatible mounting bracket (see Banner Photoelectric catalog or website for more information): • SMB30MM • SMB30A Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 Polarized Retroreflective Laser Sensors Accessory Brackets SMBQS30LT 4.5 mm (0.18") 24.0 mm (0.95" ...

  • Page 12

    ... This warranty does not cover damage or liability for the improper application of Banner products. This warranty is in lieu of any other warranty either expressed or implied. P/N 112355 rev. A Banner Engineering Corp., 9714 Tenth Ave. No., Minneapolis, MN USA 55441 • Phone: 763.544.3164 • www.bannerengineering.com • Email: sensors@bannerengineering.com Polarized Retroreflective Laser Sensors ...