S18SN6FF50Q BANNER ENGINEERING, S18SN6FF50Q Datasheet - Page 36

• Manufacturer Part Number: S18SN6FF50Q
• Description: Photoelectric Sensor
• Manufacturer: BANNER ENGINEERING
• Type: Fixed Fieldr

Specifications of S18SN6FF50Q

• Output Current: 150mA
• Sensor Output: NPN
• Supply Voltage Range Dc: 10V To 30V
• Sensing Range Max: 25mm
• Leaded Process Compatible: No
• Peak Reflow Compatible (260 C): No
• Sensor Input: Laser
• Primary Type: Photoelectric

100
T18 Series
Compact Sensors
Supply Voltage and Current
Supply Protection Circuitry
Output Configuration
Output Rating
Output Protection Circuitry
Output Response Time
Adjustments
Repeatability
Indicators
Construction
Environmental Rating
Connections
Operating Conditions
Vibration and
Mechanical Shock
Certifications
Hookup Diagrams
More information online at
10 to 30V dc (10% max. ripple); Supply current (exclusive of load current):
Opposed Mode Emitters: 25 mA
Polarized Retroreflective: 30 mA
Diffuse: 25 mA
Protected against reverse polarity and transient voltages
Solid-state complementary (SPDT) dc switch; NPN (current sinking) or PNP (current sourcing), depending on model.
The Dark Operate (DO) output may be wired as a normally open marginal signal alarm output, depending upon
hookup to the power supply.
150 mA max. (each) in standard hookup. When wired for alarm output, the total load may not exceed 150 mA;
Off-state leakage current: less than 1 mA at 30V dc;
On-state saturation voltage: less than 1V at 10 mA dc; <1.5V at 150 mA dc
Protected against false pulse on power-up and continuous overload or short circuit of outputs
Opposed: 3 milliseconds ON, 1.5 milliseconds OFF; Polarized Retroreflective, Non-polarized Retroreflective,
Fixed-field and Diffuse: 3 milliseconds ON/OFF
NOTE: 100 millisecond delay on power-up; outputs are non-conducting during this time
T18 Series infrared non-polarized retroreflective and diffuse mode models (only) have a single-turn rear-panel
SENSITIVITY control for adjustment of system gain (turn clockwise to increase)
Opposed: 375 microseconds; Polarized Retroreflective, Non-polarized Retroreflective, Fixed-field and
Diffuse: 750 microseconds. Repeatability and response are independent of signal strength.
Two LEDs: Green and Yellow
Housings are thermoplastic polyester. Lenses are polycarbonate or acrylic; one jam nut included
Leakproof design rated NEMA 6P, DIN 40050 (IP69K)
2 m or 9 m attached cable, or 4-pin Euro-style quick-disconnect fitting. QD cables are ordered separately. See page 380.
Temperature: -40° to +70° C
All models meet Mil. Std. 202F requirements. Method 201A (Vibration; frequency 10 to 60 Hz, max., double
amplitude 0.06-inch acceleration 10G). Method 213B conditions H&I (Shock: 75G with unit operating; 100G for
non-operation)
Emitters: DC03 (p. 476)
bannerengineering.com
Green ON steady: power to sensor is ON
Green flashing: output is overloaded (dc models only)
Yellow ON steady: Light Operate (LO) output is energized
Yellow flashing: excess gain marginal (1-1.5x) in light condition, LO output is energized
T18 DC Specifications
R
NPN Models: DC07 (p. 477)
Relative humidity: 90% at 50° C (non-condensing)
Opposed Mode Receivers: 20 mA
Non-polarized Retroreflective: 25 mA
Fixed-field: 35 mA
PNP Models: DC08 (p. 477)