Photoelectric Sensor

S18SN6FF50Q

Manufacturer Part NumberS18SN6FF50Q
DescriptionPhotoelectric Sensor
ManufacturerBANNER ENGINEERING
TypeFixed Field
S18SN6FF50Q datasheets
 


Specifications of S18SN6FF50Q

Output Current150mASensor OutputNPN
Supply Voltage Range Dc10V To 30VSensing Range Max25mm
Leaded Process CompatibleNoPeak Reflow Compatible (260 C)No
Sensor InputLaserPrimary TypePhotoelectric
1
2
3
4
5
6
7
8
9
10
11
Page 11
12
Page 12
13
Page 13
14
Page 14
15
Page 15
16
Page 16
17
Page 17
18
Page 18
19
Page 19
20
Page 20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
Page 13/42

Download datasheet (8Mb)Embed
PrevNext
®
MINI-BEAM
, 10-30V dc
Sensing
Models
Mode/LED*
SM312F
SM312FQD
GLASS FIBER
SM312FV
SM312FVQD
GLASS FIBER
SM312FVG
Range varies
SM312FVGQD
by sensing
GLASS FIBER
SM312FVB
SM312FVBQD
and fiber
GLASS FIBER
optics used
SM312FP
SM312FPQD
PLASTIC FIBER
SM312FPG
SM312FPGQD
PLASTIC FIBER
SM312FPB
SM312FPBQD
PLASTIC FIBER
*
Infrared LED
Visible Red LED
** For 9 m cable, add suffix W/30 to the 2 m model number (example, SM312F W/30). A model with a QD requires a mating cable (see page 380).
MINI-BEAM
10 to 30V dc (10% max. ripple) at less than 25 mA (exclusive of load)
Supply Voltage and Current
Protected against reverse polarity and transient voltages
Supply Protection Circuitry
Bipolar: One current sourcing (PNP) and one current sinking (NPN) open-collector transistor; light operate (LO) or
Output Configuration
dark operate (DO) selectable.
150 mA max. each output at 25° C, derated to 100 mA at 70° C (derate ≈ 1 mA per ° C)
Output Rating
Off-state leakage current: less than 1 µA
Output saturation voltage (PNP output): less than 1 volt at 10 mA and less than 2 volts at 150 mA
Output saturation voltage (NPN output): less than 200 millivolts at 10 mA and less than 1 volt at 150 mA
Protected against false pulse on power-up and continuous overload or short-circuit of outputs
Output Protection Circuitry
Sensors will respond to either a “light” or a “dark” signal of 1 millisecond or longer duration, 500 Hz max.
Output Response Time
0.3 millisecond response modification is available. See note below
NOTE: 100 millisecond delay on power-up: outputs do not conduct during this time.
Opposed: 0.14 milliseconds; Non-Polarized and Polarized Retroreflective, Diffuse, Convergent, Glass and
Repeatability
Plastic Fiber Optic: 0.3 milliseconds. Response time and repeatability specifications are independent of signal strength.
LIGHT/DARK OPERATE select switch, and 15-turn slotted brass screw GAIN (sensitivity) adjustment potentiometer
Adjustments
(clutched at both ends of travel). Both controls are located on rear panel of sensor and protected by a gasketed,
clear acrylic cover.
Alignment Indicating Device system (AID) lights a rear-panel mounted red LED indicator whenever the sensor sees
Indicators
a “light” condition, with a superimposed pulse rate proportional to the light signal strength (the stronger the signal,
the faster the pulse rate).
Reinforced thermoplastic polyester housing, totally encapsulated, o-ring sealing, acrylic lenses, and stainless steel screws.
Construction
Meets NEMA standards 1, 2, 3, 3S, 4, 4X, 6, 12, and 13; IEC IP67
Environmental Rating
PVC-jacketed 4-conductor 2 m or 9 m cables, or 4-pin Euro-style quick-disconnect (QD) fitting are available. QD
Connections
cables are ordered separately. See page 380.
Temperature: -20° to +70° C
Operating Conditions
Certifications
Emitters: DC03 (p. 476)
Hookup Diagrams
NOTE: DC MINI-BEAMs may be ordered with 0.3 millisecond on/off response by adding suffix MHS to the model number (example, SM312LVMHS). This modification
reduces sensing range (and excess gain).
(cont’d)
Output
Range
Cable**
Type
2 m
4-Pin Euro QD
2 m
4-Pin Euro QD
2 m
4-Pin Euro QD
Bipolar
mode
2 m
NPN/PNP
4-Pin Euro QD
2 m
4-Pin Euro QD
2 m
4-Pin Euro QD
2 m
4-Pin Euro QD
Visible Green LED
Visible Blue LED
®
DC Specifications
Relative humidity: 90% at 50° C (non-condensing)
Other Models: DC06 (p. 477)
More information online at
MINI-BEAM
®
Series
Compact Sensors
Download
PDF
Excess
Beam
Data
Gain
Pattern
Sheet
EGCG-3 &
BPG-3 &
EGCG-4
BPG-4
03368
(p. 444)
(p. 462)
EGCG-5 &
BPG-5 &
EGCG-6
BPG-6
03510
(p. 444)
(p. 462)
EGCG-7
BPG-7
50975
(p. 444)
(p. 462)
EGCG-8
BPG-8
49290
(p. 444)
(p. 462)
EGCP-3 &
BPP-3 &
EGCP-4
BPP-4
03370
(p. 447)
(p. 465)
EGCP-5
BPP-5
50975
(p. 447)
(p. 465)
EGCP-6
BPP-6
49290
(p. 447)
(p. 465)
.
bannerengineering.com
77