M126E1LDQ BANNER ENGINEERING, M126E1LDQ Datasheet
M126E1LDQ
Specifications of M126E1LDQ
Related parts for M126E1LDQ
M126E1LDQ Summary of contents
Page 1
... Excess Gain chart, page 3). M126E1LDQ *9 m (30') cables are available by adding suffix “W/30” to the model number to the cabled version (e.g., M126E1LD W/30). A model with a QD connector requires an accessory mating cable. See page 6. WARNING . . . Not To Be Used for Personnel Protection Never use these products as sensing devices for personnel protection ...
Page 2
... Temperature: 0° to 40° C (32° to 104° F); Maximum relative humidity: 90% at 40° C (non-condensing) Laser Classification Class 1 laser product; complies with 21 CFR 1040.10, EN 60825-1:2001 except for deviations pursuant to laser notice No. 50, dated 7-26-01 Certifications 2 P/N 53808 rev. B M12 Class 1 Laser Emitter Specifications Banner Engineering Corp. Minneapolis, U.S.A. • Website: http://www.baneng.com • Tel: 763.544.3164 ...
Page 3
... Aperture/Caution Label (Do not clamp only in this area) ø12.7 mm (0.50") Banner Engineering Corp. Minneapolis, U.S.A. • Website: http://www.baneng.com • Tel: 763.544.3164 M12 Class 1 Laser Emitter M12 Dimensions See "Connections" in Specifications 57 mm (2.25") Excess Gain Excess Gain of the M12 emitter is dependent on the particular receiver used. ...
Page 4
... Allen wrench) until the laser is accurately aligned. Figure 2. Three possible M12 orientations 4 P/N 53808 rev. B Figure 1. Model SMB127 mounting block Figure 1a. Mounting bracket model SMB46X3, front and rear views Banner Engineering Corp. Website: http://www.baneng.com • Tel: 763.544.3164 Minneapolis, U.S.A. • ...
Page 5
... M12 Figure 5. At long distances, use retroreflective tape to locate the beam at the receiver location. Never use a mirror as an alignment target. Banner Engineering Corp. Minneapolis, U.S.A. • Website: http://www.baneng.com • Tel: 763.544.3164 Approx Approx. 0.5mrad = 0.029º Conventional modulated infrared LED photoelectric emitters are designed with beam divergence angles of several degrees ...
Page 6
... Laser beam enable + 10-30V dc - Mounting Bracket Dimensions 2x 11.4 mm (0.45") 60º 10.6 mm (0.42 ") 12.9 mm (0.508") 60º 17.8 mm (0.70") 61.0 mm (2.40") M126E1LDQ Laser Diode Emitter 3-pin Pico-style Connector Laser beam bk enable bn + 10-30V SMB127 Mounting Block 36 mm (1.4") 12.9 mm (0.508") 23.6 mm (0.93") 21.6 mm (0.85" ...
Page 7
... Temperature: -40º to +90°C (-40º to +194°F) Voltage Rating: 30V ac/36V dc Environmental Rating: None Model Style 3-Pin PKG3 (6.5') Straight Banner Engineering Corp. Minneapolis, U.S.A. • Website: http://www.baneng.com • Tel: 763.544.3164 Accessories Mounting Brackets Description 3/64" Shortarm hex key 4 Set screws ...
Page 8
... M12 Class 1 Laser Emitter WARRANTY: Banner Engineering Corp. warrants its products to be free from defects for one year. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture found to be defective at the time it is returned to the factory during the warranty period ...