S18UUAQ BANNER ENGINEERING, S18UUAQ Datasheet

Ultrasonic Sensor

S18UUAQ

Manufacturer Part Number
S18UUAQ
Description
Ultrasonic Sensor
Manufacturer
BANNER ENGINEERING
Datasheet

Specifications of S18UUAQ

Sensing Range Min
30mm
Sensing Range Max
300mm
Switching Frequency
300kHz
External Diameter
18mm
Operating Temperature Range
-20°C To +60°C
Supply Voltage
30VDC
Frequency
300kHz
Body Material
Thermoplastic Polyester
Contact Rating
65 MA
Printed in USA
* 9 m cables are available by adding suffix “W/30” to the model number of any cabled sensor (e.g., S18UUA W/30).
Straight Housing
A model with a QD connector requires a mating cable; see page 10.
S18UUA
S18UUAQ
S18UIA
S18UIAQ
S18UUAR
S18UUARQ
S18UIAR
S18UIARQ
!
Number
Model
Information about discrete models is available on Banner’s website: www.bannerengineering.com
WARNING . . .
Never use these products as sensing devices for personnel protection. Doing so could lead to serious injury or death.
These sensors do NOT include the self-checking redundant circuitry necessary to allow their use in personnel safety
applications. A sensor failure or malfunction can cause either an energized or de-energized sensor output condition.
Consult your current Banner Safety Products catalog for safety products which meet OSHA, ANSI and IEC standards for
personnel protection.
Right-Angle Housing
30 to 300 mm
(1.2" to 11.8")
Sensing
Range
Not To Be Used for Personnel Protection
5-wire, 2 m (6.5') cable
5-pin Euro style QD
5-wire, 2 m (6.5') cable
5-pin Euro style QD
5-wire, 2 m (6.5') cable
5-pin Euro style QD
5-wire, 2 m (6.5') cable
5-pin Euro style QD
• Fast, easy-to-use TEACH-Mode programming; no potentiometer adjustments
• Short dead zone
• Scalable output automatically distributes the output signal over the width of the
• Two bi-colored status LEDs
• Rugged encapsulated design for harsh environments
• Choose 2 meter or 9 meter unterminated cable, or 5-pin Euro-style QD connector
• Wide operating range of -20° to +60°C (-4° to +140°F)
• Choose either straight or right-angle housing
• Temperature compensation
• Selectable response times of 2.5 or 30 ms
• Select analog models with either 0-10V dc or 4-20 mA output
U-GAGE
18 mm Ultrasonic Sensors with TEACH-mode programming
programmed sensing window
Cable*
Models
S18U Series Sensors with Analog Output
02/05
10 to 30V dc
Voltage
Supply
Features
0 to 10V dc
0 to 10V dc
4 to 20 mA
4 to 20 mA
Output
Ultrasonic Proximity Mod
P/N 110738 rev. A
Configuration
Right-Angle
Housing
Straight
Ultrasonic

Related parts for S18UUAQ

S18UUAQ Summary of contents

Page 1

... Right-Angle Housing Straight Housing Model Sensing Number Range S18UUA S18UUAQ S18UIA S18UIAQ 30 to 300 mm (1.2" to 11.8") S18UUAR S18UUARQ S18UIAR S18UIARQ * 9 m cables are available by adding suffix “W/30” to the model number of any cabled sensor (e.g., S18UUA W/30). A model with a QD connector requires a mating cable; see page 10. ...

Page 2

... P/N 110738 rev distance from the sensor to the target c = speed of sound in air t = transit time for the ultrasonic pulse C = speed of sound in meters per second m temperature in ° speed of sound in feet per second ft temperature in °F F Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 ...

Page 3

... Output Indicator PWR OUT LED LED TEACH Push Button TEACH Figure 1. Sensor features Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 U-GAGE S18U Series Sensor — Analog Output ™ Sensor Programming Two TEACH methods may be used to program the sensor: • ...

Page 4

... Output LED: Flashing Red Teach Unacceptable Output LED: ON Red Power LED: Must be ON Green Teach Accepted (Sensor learns the 10V limit Output LED: Yellow or OFF Teach Unacceptable Output LED: Flashing Red Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 Far Far ...

Page 5

... Position the target for the center of the window • “Click” the push button • Without moving the target, “click” the push button again Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 U-GAGE S18U Series Sensor — Analog Output ™ ...

Page 6

... Not available via push button 6 P/N 110738 rev. A Procedure Remote Wire T 0.04 sec. < T < 0.8 sec • Four-pulse the remote line Result • Push buttons are either enabled or disabled, depending on previous condition. Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 ...

Page 7

... Application Notes Objects passing inside the specified near limit may produce a false response. Certifications * Linearity and resolution are specified using (2" x 2") aluminum plate at 22°C under fixed sensing conditions. Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 U-GAGE S18U Series Sensor — ...

Page 8

... Hookups +10 - 30V Maximum Target Rotation Angle Aluminum target used 100 mm 150 mm 200 mm 250 mm Sensing Distance QD Models bn +10 - 30V 10V 30V dc (fast (slow Remote Teach shield Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 300 mm bn shield ...

Page 9

... Cabled Models 6.0 mm (0.24") 80.8 mm (3.18") 53.8 mm (2.12") Cabled Models 85.1 mm (3.35") 58.0 mm (2.29") Transducer 6.0 mm (0.24") Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 U-GAGE S18U Series Sensor — Analog Output ™ Dimensions Straight Housing Transducer 10.6 mm (0.42") 18.0 mm (0.71" ...

Page 10

... Accessories Quick-Disconnect Cables Length Dimensions 2 m (6.5 (15 (30 max. (1.7" max. (1.5" (6.5 (15 (30') M12 x 1 ø (0.6") Pinout ø (0.6") M12 x 1 White Brown Blue Black Gray 38 mm max. (1.5") Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 ...

Page 11

... Thru 63.5 mm (2.50") 71.1 mm 2.7 mm (2.80") (0.10") Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 U-GAGE S18U Series Sensor — Analog Output ™ Mounting Brackets SMB18SF 41 mm (1.6") M18 x 1 internal thread 20.8 mm (0.82" ...

Page 12

... P/N 110738 rev A. Banner Engineering Corp., 9714 Tenth Ave. No., Minneapolis, MN USA 55441 • Phone: 763.544.3164 • www.bannerengineering.com • Email: sensors@bannerengineering.com WARRANTY: Banner Engineering Corp. warrants its products to be free from defects for one year. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture found to be defective at the time it is returned to the factory during the warranty period ...

Related keywords