SLM80B6 BANNER ENGINEERING, SLM80B6 Datasheet - Page 3

• Manufacturer Part Number: SLM80B6
• Description: Ultrasonic Slot Sensor
• Manufacturer: BANNER ENGINEERING
• Type: Opposed Moder

Specifications of SLM80B6

• Sensing Range Min: 1.5mm
• Sensing Range Max: 80mm
• Operating Temperature Range: -20°C To +60°C
• Supply Voltage: 30VDC
• Body Material: Die-cast Zinc
• Sensor Terminals: Cable
• Features: Opposed-Mode
• Brand/series: SLM
• Current, Switching: 100 mA
• Function: Vane
• Ip Rating: IP67
• Output: NPN/PNP
• Primary Type: Photoelectric
• Range, Measurement: 80 mm
• Sensing Mode: Opposed
• Technology: Photoelectric
• Termination: 4-Wire Cable
• Voltage, Supply: 30 VDC
• Accessories Available: Cordsets
• Contact Rating: 25 MA
• Sensor Output: NPN/PNP
• Sensor Body Material: Die-cast Zinc

***Repeatability: Variation in switching distance for a standard target at controlled sensing conditions
**Hysteresis: Distance an object must move to toggle between output OFF and output ON state
Slot Opening
Supply Voltage and Current
Supply Protection Circuitry
Output Configuration
Output Rating
Output Protection Circuitry
Minimum Object Detection*
at Max. Gain
Minimum Object Detection*
at 2X Excess gain
Hysteresis**
Repeatability***
Output Response Time
Repeatability
Adjustments
Indicators
Construction
Environmental Rating
Connections
Operating Conditions
Certifications
* Minimum Object Detection: Smallest diameter rod that can be detected when passed slowly through sensing beam
NOTE: Minimum object detection is measured midway between the emitter and receiver. For best results, objects to be detected should be placed in the midway position
Banner Engineering Corp. • Minneapolis, MN U.S.A
www.bannerengineering.com • Tel: [phone]
when possible. The minimum object detection size may increase if the object is very close to the receiver side.
10, 20, 30, 50, 80, 120, 180, or 220 mm (depending on model); beam is 5 mm (0.2") from outer edge
10 to 30V dc (10% ripple) @ less than 25 mA, exclusive of load
Protected against reverse polarity and transient voltages
Cabled and Euro-style QD models: Bipolar: One current sourcing (PNP) and one current sinking (NPN)
Pico-style QD models: Current sourcing (PNP) or current sinking (NPN), depending on model
100 mA with short circuit protection
OFF-state leakage current: < 10 µA sourcing; < 200 µA sinking
ON-state saturation voltage:
Protected against output short-circuit and false pulse on power up. 100 ms max. delay at power up; outputs do not
conduct during this time.
500 microseconds
95 microseconds
1-turn potentiometer Sensitivity adjustment
Light Operate / Dark Operate selection switch
Two LED Indicators: Power (green) and Output (yellow)
Green ON steady: Power ON
Green flashing:
Yellow ON steady: Output is activated
Housing: Die-cast zinc with yellow paint; model numbers with suffix “N” have nickel plating
Endcaps: ABS
Optic windows: acrylic
IEC IP67 (NEMA 6)
Cabled models: 2 m (6.5') or 9 m (30') 4-conductor, PVC-jacketed cable
Pico-style QD models: 3-pin, threaded integral QD connector
Euro-style QD models: 150 mm (6") pigtail (polyurethane) cable with 4-pin, threaded connector
Temperature: –20° to +60° C (– 4° to +140° F)
Max. Relative Humidity: 95% @ 55° C (non-condensing)
SLM10…
1.00 mm
0.30 mm
0.10 mm
0.02 mm
(0.040")
(0.012")
(0.004")
(0.001")
NPN: 1.6V @ 100 mA
PNP: 2.0V @ 100 mA
SLM20…
1.25 mm
0.30 mm
0.10 mm
0.02 mm
(0.050")
(0.012")
(0.004")
(0.001")
Sensor short circuit
Specifications
SLM30…
1.50 mm
0.40 mm
0.10 mm
0.02 mm
(0.060")
(0.016")
(0.004")
(0.001")
SLM50…
1.65 mm
0.60 mm
0.10 mm
0.04 mm
(0.065")
(0.024")
(0.004")
(0.002")
SLM Series Slot Sensors
SLM80…
1.80 mm
0.75 mm
0.20 mm
0.06 mm
(0.070")
(0.030")
(0.008")
(0.002")
SLM120…
1.80 mm
0.90 mm
0.20 mm
0.08 mm
(0.070")
(0.035")
(0.008")
(0.003")
SLM180…
1.80 mm
0.90 mm
0.20 mm
0.08 mm
(0.070")
(0.035")
(0.008")
(0.003")
P/N 122703 rev. D
SLM220…
2.40 mm
1.00 mm
0.20 mm
0.08 mm
(0.095")
(0.039")
(0.008")
(0.003")
3