T30UUPBQ BANNER ENGINEERING, T30UUPBQ Datasheet
T30UUPBQ
Specifications of T30UUPBQ
Related parts for T30UUPBQ
T30UUPBQ Summary of contents
Page 1
... T30UIPBQ (11.8" to 79") T30UUNB 128 kHz T30UUNBQ T30UUPB T30UUPBQ *NOTES: • (30') cables are available by adding suffix “W/30” to the model number of any cabled sensor (e.g., T30UINA/30). • A model with a QD connector requires an optional mating cable, see page 9. Printed in USA U-GAGE ™ ...
Page 2
... NOTE: The sensor allows for some forgiveness in this procedure. If the two limits are not exactly the same (but closer than the minimum 10-mm window required), the sensor will put the set point at the “average” of the two limits. 2 P/N 57438 Rev. C Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 ...
Page 3
... The sensor will return to RUN mode if the first TEACH condition is not registered 2. After the first limit is taught, the sensor will remain in PROGRAM mode until the 3. Press and hold the programming push button > 2 seconds (before teaching the Banner Engineering Corp. Minneapolis, MN U.S.A. • ...
Page 4
... P/N 57438 Rev. C > 0.8 sec T Teach Second Discrete Limit T > 0.8 sec T Teach First Teach Second Analog Limit Analog Limit > 0.8 sec Teach First Limits Teach Second Limits Push Button Lockout Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 ...
Page 5
... Far Window Window Target Position Figure 3. Output current as a function of target position Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 ™ T30 Series with Analog and Discrete Outputs RUN Mode NOTE: All LED indicators momentarily go OFF when sensor changes state between PROGRAM and RUN modes ...
Page 6
... ON = Ready for first window limit { Yellow analog Flashing = Ready for second limit OFF = Not teaching analog limits ON = Ready for first window limit { Yellow discrete Flashing = Ready for second limit OFF = Not teaching discrete limits Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 ...
Page 7
... Distance Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 ™ T30 Series with Analog and Discrete Outputs U-GAGE T30 Series Performance Curves 400 mm 8.0 in 300 mm 6.0 in 200 mm 4.0 in ...
Page 8
... Quick-Disconnect Models 66.5 mm (2.62 in) Cabled PNP bu – 12-24V † Analog bk †† Discrete Remote Teach gy shield* Quick-Disconnect PNP bu – 12-24V † Analog bk †† Discrete gy Remote Teach shield* Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 ...
Page 9
... (1.58") 6.3 mm (0.25")* * Use 5 mm (#10) screws to mount bracket. ø 6.3 mm (0.25")* 7.6 mm (0.30") Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 ™ T30 Series with Analog and Discrete Outputs Accessories Quick-Disconnect (QD) Cables Connector Style 5-Pin Euro-style ø Right-angle (0.6" ...
Page 10
... Nut Plate Screw (2) • split clamp with swivel, black reinforced thermoplastic polyester • Stainless steel hardware included 50.8 mm (2.00") 12 1.5 mm (0.50") internal thread 30.0 mm (1.18") 66.5 mm 29.0 mm (2.62") (1.14") Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 ...
Page 11
... U-GAGE ™ Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 T30 Series with Analog and Discrete Outputs 11 P/N 57438 Rev. C ...
Page 12
... Products catalog for safety products which meet OSHA, ANSI and IEC standards for personnel protection. WARRANTY: Banner Engineering Corp. warrants its products to be free from defects for one year. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture found to be defective at the time it is returned to the factory during the warranty period. ...