S662-1-1-2-0-0 Simpson, S662-1-1-2-0-0 Datasheet

Batch Counter

S662-1-1-2-0-0

Manufacturer Part Number
S662-1-1-2-0-0
Description
Batch Counter
Manufacturer
Simpson
Datasheet

Specifications of S662-1-1-2-0-0

No. Of Digits / Alpha
6
Digit Height
14.2mm
Power Consumption
3VA
Counting Speed
20kHz
Operating Temperature Range
0°C To +40°C
Signal Input Type
Pulse
Panel Cutout Height
1.77"
Meter Output
Two Relay
Equipment Type
Dual Counter
Modes
Dual, Totalizing/Batch
Counter Supply Voltage
120VAC
Rohs Compliant
NA
Lead Free Status / RoHS Status
na
Lead Free Status / RoHS Status
na
• Easily programmed from the front panel
• Remote Reset capability
• Input variety: Quadrature, Switch, TTL,
• Software functions include:
The S662 is a multi-function counter that can be easily configured to
operate either in a dual mode or in a totalizing/batch mode, each
with separate scaling and reset functions. When functioning in the
dual mode, full direction control is maintained for the totalizing and
batch counts. In the totalizing batch mode, the secondary value
(batch count) is incremented after the primary totalizing count has
completed its cycle.
The counter is powered from 120 or 240VAC and has a non-volatile
EEPROM to retain all programming and count information when the
power source is removed or interrupted. An option 12DCV excitation
output module can provide power for external sensors.
This versatile counter has latching, boundary or timed (0.01 to
599.99 seconds) output modes.
Mounting Requirements
The S660 series 1/8 DIN counters require a panel cutout of 1.77"
(45mm) high by 3.62" (92mm) wide. To install the counter into a
panel cutout, remove the clips from the side of the meter. Slide the
meter through your panel cutout, then slide the mounting clips back
on the meter. Press evenly to ensure a proper fit.
CMOS, NAMUR, PNP, NPN
Password
Set Point Programming
Display Scaling
Decimal Point Selection
For more information, visit www.simpsonelectric.com
Specifications
DISPLAY
Type
Height
Decimal Point
Count Direction
Display Range
Output Indicators
POWER REQUIREMENTS
AC Voltages
Power Consumption
INPUT RATINGS
Current Sinking
Current Sourcing
Minimum Pulse Width
Low Pass Filter
Low Bias
High Bias
Count Rate
Maximum Voltage Input
A, B, and User
INPUT
User Input
Standard Input
Quadrature Input
ENVIRONMENTAL
Operating Temp.
Storage Temp.
Relative Humidity
Ambient Temperature
Temp. Coefficient (per °C)
Warmup Time
MECHANICAL
Bezel
Depth
Panel Cutout
Case Material
Weight
Ordering Information
Basic Unit
S662
120 ACV
240 ACV
Power Supply
Standard
Quadrature
1
2
Input
6-digit, 7-segment, red LED
0.56" (14.2mm)
User-programmable
"+" indication implied, "-" indication displayed
-99,999 to +999,999
1 and 2
120, 240VAC, ±10%
3VA
10K , 5% Resistor pull-up to (9.0 - 16DCV) ±10%
5.1K , 5% Resistor pull-down to common
~5µs
<200Hz
VLT = 1.6V ±10% VUT = 3.6V ±10%
VLT = 5.0V ±10% VUT = 7.0V ±10%
20KHz (Pulse Max) 5KHz (Quadrature X4 Max)
30DCV (Max)
(Second channel reset) Count on the second chan-
nel is reset when the User Input is pulled low.
VLT
VLT
0°C to +40°C
-10°C to +60°C
0-80% non-condensing for temperatures less
than 32°C, decreasing linearly to 50% at 40°C
25°C
±100ppm/ °C
15 minutes
3.93" x 2.04" x .52" (99.8mm x 51.8mm x 13.2mm)
3.24" (82.3mm)
3.62" x 1.77" (92mm x 45mm)
PBT-ABS
9oz (255.1g)
None
One Relay
Two Relays
0.2DCV guaranteed low, VUT = 3.0DCV (max)
0.9DCV VUT =3.15DCV (max)
1
2
Output
0
1
2
(100mA max cur-
Excitation
12DCV
None
rent)
None
Other
0
1
0

Related parts for S662-1-1-2-0-0

S662-1-1-2-0-0 Summary of contents

Page 1

... Display Scaling Set Point Programming Decimal Point Selection The S662 is a multi-function counter that can be easily configured to operate either in a dual mode totalizing/batch mode, each with separate scaling and reset functions. When functioning in the dual mode, full direction control is maintained for the totalizing and batch counts ...

Page 2

... Dimensions - S660, S661, S662, S663, S664 Accessories Chariot The Chariot is used to mount most cube- style quadrature encoders and measuring wheels. Made of anodized aluminum, the chariot includes mounting hardware and selectable pivotal points. Wheels, tires, and flexible shaft couplings are sold sepa- rately ...

Related keywords