C48CB003 Red Lion Controls, C48CB003 Datasheet - Page 5

• Manufacturer Part Number: C48CB003
• Description: C48C (3P,R,SNK,RLY)
• Manufacturer: Red Lion Controls
• Type: Counterr

Specifications of C48CB003

• Rohs Compliant: YES
• Connection Type: Screw
• Cut Out, Panel: 1/16 DIN
• Digit Height: 0.3
• Dimensions: 4.17"L×1.95"W×1.95"H
• Display Digit Height: 0.3" (Main), 0.2" (Secondary)
• Display Type: LCD
• Function: Counter
• Material, Casing: Plastic
• Number Of Digits: 6
• Primary Type: Electronic
• Range, Measurement: 0.00001 to 9.99999
• Special Features: programmable
• Voltage, Supply: 85 to 250 VAC
• Sealing: NEMA 4X/IP65
• Power Requirements: 85 to 250 VAC
• Operating Temperature: 0 to +50°C
• Panel Cutout: 1.77" × 1.77" (1⁄16 DIN)
• Lead Free Status / Rohs Status: RoHS Compliant part

MULTIPLE UNIT STACKING
stacked either horizontally or vertically. For vertical stacking, install the panel
latch with the screws to the sides of the unit. For horizontal stacking, the panel
latch screws should be at the top and bottom of the unit. The minimum spacing
SLOW DOWN & CUT TO LENGTH WITH TOTAL FOOTAGE
installing cut to length counters on the roll form machines. Currently, electro-
mechanical counters are used for length measurements. The operator slows
the machine down upon arriving at the desired length, stops and then cuts. The
addition of the C48CB batch counters eliminates the operator’s manual
observation and control.
preprogrammed for tracking and will automatically follow Preset 2. Preset 1
is used as the slow down, and is set for a value 0.25 yards less than Preset 2.
The process count is programmed to automatically reset at the Preset 2 cut
length of 11.00 yards, and begin counting for the next roll. Counter 2 is
programmed as a totalizer and is recorded and reset (via key switch) at the end
of the operator’s shift. The C48CB was ordered with the RS-485 serial
communication option. Future plans include a data acquisition program to
interrogate the C48CB’s. A 100 ppr rotary pulse generator is shaft coupled to
a 4" pinch roller for length measurement. Display units desired is 0.01 yards.
Program Security features are set to allow access to Preset 2 only. This allows
the operator to change the required cut length, but prevents acidental changes
to other programming parameters that may adversely affect process operation.
After all programming is complete, the Program Disable DIP switch is moved
to the up position to enable the Program Security function.
Circumference Of Pinch Roller:
Pulses Per Yard:
Prescaler:
Products:
PANEL LATCH INSTALLED FOR VERTICAL
The C48C is designed for close spacing of multiple units. Units can be
To improve production efficiency, a wallpaper manufacturing plant is
The operator programs the required cut length as Preset 2. Preset 1 is
circumference =
36
2.8647913 rev/yard
Prescaler =
Prescaler = 0.34907
C48CB108
RPGQ0100
1
i
y
n
a
12.56636 = 3.14159
c
r
h
d
es
=
UNIT STACKING
nu
286
12.
D
m
1
1
56
i
.4
sp
b
0
re
7
e
0
6
l
r
913
v
36”
a
o
y
100 ppr/rev = 286.47913 pulses/yard
f
diameter
u
p
n
= 2.8647913 rev/yard
u
i
l
t
s
s
es
4.00
PANEL LATCH INSTALLED FOR
HORIZONTAL UNIT STACKING
5
from center line to center line of the units is 1.96" (49.8 mm). This spacing is
the same for vertical or horizontal stacking.
Note: When stacking units, provide adequate panel ventilation to ensure that
PROGRAMMING
the maximum operating temperature range is not exceeded.
EntrY
Ac PSc
PScALr
dEc Pt
Cnt In
OPEr 1
C2 ASn
OPEr 2
Ac PrS
PrESEt
PrESEt
PrESEt
P1trAc
Ac Out
OutrES
OutPut
OutPut
OutPut
rEVOut
rEVAnu
OutP. u P
USrIn1
USr F1
CodE
ScroLL
SErSEt
SErAdr
SErAbr
PrnOPt
PrnrSt
FAcSEt
PANEL CUT-OUT SPACING FOR MULTIPLE UNIT STACKING.
AutoSc
-L
0. 3 4907
----. - -
qUAd 1
12
totAL
02
-L-y-L
PRS1
PRS2
PRS3
yES
-L-L-L
0. 0 1SEC
1
2
3
-n-n-n
-n-n-n
-F-F-F
rSt. 2 -E
rSt. - E
no
96o
00
no
08
no
no
t 0. 1 0
t 1. 0 0
t 0. 1 0
(locked)
003
10. 7 5
11. 0 0
9000. 0 0
HORIZONTAL ARRANGEMENT SHOWN.
(value 0.25 less than PRS2 for slowdown)
(cut length)
(Set high so output does not activate)