859-802 WAGO, 859-802 Datasheet
859-802
Manufacturer Part Number
859-802
Description
Terminal Block With DC/DC Converter
Manufacturer
WAGO
Datasheet
1.859-802.pdf
(1 pages)
Specifications of 859-802
Dc / Dc Converter O/p Type
Fixed
No. Of Outputs
1
Input Voltage
15V To 30V
Power Rating
5W
Output Voltage
10VDC
Output Current
0.5A
Approval Bodies
UL, CE
Supply Voltage
24VDC
Rohs Compliant
Yes
Electronic Terminal Block with DC-DC Converter
Step Down Converter DC 24 V / DC 10 V
WAGO Kontakttechnik GmbH & Co. KG
Subject to design changes
05.06.2008 / d680200e.doc
Description
•
•
Application:
When industrial controls that typically require DC 24 V are
used in conjunction with industrial sensors operating at DC 10
V, often interface devices are required.
This module can cost effectively produce DC 10 V at up to
500 mA from a 24 V source.
DC/DC Converter 24 V / 10 V ; 0.5 A
End plate 859-525 included and attached.
Mounting on DIN 35 rail.
Similar photo
Postfach 2880 • D-32385 Minden
Hansastr. 27 • D-32423 Minden
Technical Data
Input nominal voltage U
Input voltage range
Output voltage
Output voltage range
Max. output current
Max. line regulation
Max. load regulation
Efficiency
Output noise and ripple
Switching frequency
Isolation
Input polarity protection
Minimum load requirements
Max. Transient recovery time
Max. start-up time
Max. hold-up time
Input protection
Output short circuit protection Momentary (Output can be shorted for
Temperature coefficient
Ambient operating temperature -25 °C...+55 °C
Terminal block width
Wire connection
Stripped length
Approvals
COM (GND)
Tel.:
Fax.:
+24 V
05 71 / 8 87-0
05 71 / 8 87-169 Web:
N
Item-No.
859-802
DC 24 V
DC 15-30 V
DC 10 V
DC 10 V ± 2 %
500 mA
0.5 % (from DC 15-30 V, full load)
0.7 % (no load to full load, DC 24 V in)
85 % (DC 24 V in, full load)
20 mV P-P (at bandwidth 20 MHz)
200 kHz (nominal)
Non-isolated
Yes
None
500 µs (Recovery time for a step load
change of 25 % to 75 % of full load)
3 ms (DC 24 V in, full load)
500 µs (DC 24 V in, full load)
TVS Diode
1 minute without damaging the device)
100 ppm/°C typ.
6 mm / 0.236 in
CAGE CLAMP®
0.08-2.5 mm
5-6 mm / 0.22 in
C
UL508
E175199
C
UL1604 / CSA22.2 No.213
E198726
E-Mail:
UL
UL
US
US
info@wago.com
http://www.wago.com
2
/ AWG 28-14
+10 V
+10 V
COM (GND)
Pack.-unit
pcs
D a t a s h e e t
1
1/1
Related parts for 859-802
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
JUMPER BAR, 2WAY
Manufacturer:
WAGO
Datasheet:
Part Number:
Description:
JUMPER BAR, 10WAY
Manufacturer:
WAGO
Datasheet:
Part Number:
Description:
DIN Mount Relay
Manufacturer:
WAGO
Datasheet:
Part Number:
Description:
POWER RELAY, 1CO, 24VAC/DC, 5A, DIN RAIL
Manufacturer:
WAGO
Datasheet:
Part Number:
Description:
POWER RELAY, 1CO, 115VAC/110VDC DIN RAIL
Manufacturer:
WAGO
Datasheet:
Part Number:
Description:
POWER RELAY, 1CO, 12VAC/DC, 5A, DIN RAIL
Manufacturer:
WAGO
Datasheet:
Part Number:
Description:
4 CHAN DIG INPUT 5VDC .2mS
Manufacturer:
WAGO
Datasheet: