LSM-1.5/10-D5-C Murata Power Solutions Inc, LSM-1.5/10-D5-C Datasheet
LSM-1.5/10-D5-C
Specifications of LSM-1.5/10-D5-C
Related parts for LSM-1.5/10-D5-C
LSM-1.5/10-D5-C Summary of contents
Page 1
... DATEL's LSM D5 Series for SMT (surface-mount) are non-isolated DC/ DC converters that accept a 5V input (4.5V to 5.5V input range) and deliver 0.8V, 1V, 1.2V, 1.5V, 1.8V, 2V, 2.5V, or 3.3V outputs at 10 Amps. LSM D5 SMT's are designed to take on-board 5V power and convert it, with the highest efficiency in the smallest space, to any lower voltage required by today's current-hungry DSP's, ASIC's and CPLD's ...
Page 2
... Pin Function P63 1 On/Off Control 2 +Input 3 Common 4 +Output 5 V Trim OUT 6 +Sense Technical enquiries email: sales@murata-ps.com, tel: MDC_LSM10A-D5.B01 Page Package (Case, Pinout) C45, P63 C45, P63 C45, P63 C45, P63 C45, P63 C45, P63 C45, P63 C45, P63 +1 508 339 3000 ...
Page 3
... Performance/Functional Specifications Table is not implied I/O Filtering and Noise Reduction All models in the LSM D5 Series are tested and specified with external 22μF tantalum input and output capacitors. These capacitors are necessary to accommodate our test equipment and may not be required to achieve desired performance in your application ...
Page 4
... See Typical Performance Curves. Remote Sense LSM D5 SMT Series DC/DC converters offer an output sense function on pin 6. The sense function enables point-of-use regulation for overcoming moderate IR drops in conductors and/or cabling. Since these are non-isolated devices whose inputs and outputs usually share the same ground plane, sense is provided only for the +Output ...
Page 5
... If the output current exceeds it maximum rating by typically 70% (17 Amps the output voltage drops to less than 98 original value, the LSM D5's internal overcurrent-detection circuitry immediately turns off the converter, which then goes into a "hiccup" mode. While hiccupping, the converter will continuously attempt to restart itself, go into overcurrent, and then shut down ...
Page 6
... O – – you may deduce from the derating curves and observe in the efficiency O curves on the following pages, LSM D5 SMT's are more efficient at lower current levels. Also I – 1 – lower current levels. Consequently, LSN-D5 SMT's deliver very impressive temperature performance if operating at less than full load. ...
Page 7
... Therefore it is difficult to give cap values which serve all applications. Some experimentation may be required. www.murata-ps.com LSM-10A D5 Models , 0.8-3.3V 10A, DC/DC's in SMT Packages IN OUT, Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000 MDC_LSM10A-D5.B01 Page ...
Page 8
... Typical Performance Curves for LSM-10A D5 SMT Series LSM-1/10-D5 Efficiency vs. Line Voltage and Load Current 4. 5. Load Current (Amps) LSM-1.2/10-D5 Efficiency vs. Line Voltage and Load Current 4. 5. Load Current (Amps) LSM-1.5/10-D5 Efficiency vs. Line Voltage and Load Current 4. 5. Load Current (Amps) www.murata-ps.com ...
Page 9
... Typical Performance Curves for LSM-10A D5 SMT Series LSM-1.8/10-D5 & LSM-2/10-D5 Output Current vs. Ambient Temperature (SMT mount, air flow direction from pin 2 to pin Natural Convection 6 100 lfm – Ambient Temperature ( C) LSM-1.8/10-D5 Efficiency vs. Line Voltage and Load Current 4. 5. Load Current (Amps) LSM-2/10-D5 Efficiency vs ...
Page 10
... Typical Performance Curves for LSM-10A D5 SMT Series at V Start-Up from ON/OFF (I = 1V/10A 22μF) OUT IN OUT V IN 2V/div V OUT 1V/div 2msec/div Start-Up from 1V/10A 22μF) OUT IN OUT V IN 2V/div V OUT 1V/div 2msec/div Input Reflected Ripple Current (Input Filter = 220μF/12μH/33μF, I ...
Page 11
... Typical Performance Curves for LSM-10A D5 SMT Series at V Output Ripple and Noise (V = 3.3V/10A 22μ 20MHz) OUT IN OUT 20mV/div 1μsec/div Dynamic Load Response (V = 3.3V 10A Step OUT IN 100mV/div 100μsec/div Dynamic Load Response ( 10A Step OUT IN OUT 50mV/div 100μsec/div Single Output, Non-Isolated, 5V 20mV/div = 22μ ...
Page 12
... Tape & Reel Surface Mount Package DATEL's LSM series DC/DC converters are the only higher-current (10A) SMT DC/DC's that can be automatically "pick-and-placed" using standard vacuum-pickup equipment (nozzle size and style, vacuum pressure and placement speed may need to be optimized for automated pick and place) and subsequently refl ...
Page 13
... DATEL's new-generation LSM SMT DC/DC converters are shipped in quantities of 150 modules per tape and reel. 2.205 2.063 1.370 (52.4) (34.8) (56) DIMENSIONS IN INCHES (mm) 0.590 (14.97) 2.44 (62.0) Murata Power Solutions, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A. Tel: (508) 339-3000 (800) 233-2765 Fax: (508) 339-6356 www ...