PTH05060WAD ARTESYN, PTH05060WAD Datasheet - Page 2

• Manufacturer Part Number: PTH05060WAD
• Description: CONVERTER, DC/DC, 0.8-3.6V/10A
• Manufacturer: ARTESYN

Specifications of PTH05060WAD

• Output Type: Variable
• No. Of Output Channels: 1
• Input Voltage: 4.5V To 5.5V
• Power Rating: 21.6W
• Output Current: 10A
• Supply Voltage: 5V
• Dc / Dc Converter Case Style: Through Hole
• External Depth: 8.5mm
• Dc / Dc Converter O/p Type: Variable
• No. Of Outputs: 1
• Approval Bodies: CUL / EN / UL
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Part Number System with Options
N N o o t t e e s s
1
2
3
4
5
6
7
8
9
10
For the most current data and application support visit www.artesyn.com/powergroup/products.htm
DC-DC CONVERTERS
OUTPUT
POWER
(MAX.)
21.6 W
Remote ON/OFF. Positive Logic
ON:
OFF:
See Figure 1 for safe operating curve.
A 100 µF electrolytic input capacitor is required for proper operation. The
capacitor must be rated for a minimum of 300 mA rms of ripple current.
An external output capacitor is not required for basic operation. Adding
100 µF of distributed capacitance at the load will improve the transient
response.
1 A/µs load step, 50 to 100% I
If utilized Vout will track applied voltage by ±0.3 V (up to Vo set point).
The pre-bias start-up feature is not compatible with Auto-Track ™ . This is
because when the module is under Auto-Track ™ control, it is fully active
and will sink current if the output voltage is below that of a back-feeding
source. Therefore to ensure a pre-bias hold-off, one of the following two
techniques must be followed when input power is first applied to the
module. The Auto-Track ™ function must either be disabled, or the
module’s output held off using the Inhibit pin. Refer to Application Note
158 for more details
Tape and reel packaging only available on the surface-mount versions.
To order Pb-free (RoHS compatible) surface-mount parts replace the
mounting option ‘S’ with ‘Z’, e.g. PTH05050WAZ. To order Pb-free
(RoHS compatible) through-hole parts replace the mounting option ‘H’
with ‘D’, e.g. PTH05050WAD.
NOTICE: Some models do not support all options. Please contact your
local Artesyn representative or use the on-line model number search tool at
http://www.artesyn.com/powergroup/products.htm to find a suitable
alternative.
Pin 3 open; or V > Vin - 0.5 V
Pin 3 GND; or V < 0.8 V (min - 0.2 V).
4.5-5.5 Vdc
VOLTAGE
INPUT
.
Mechanical Package
Point of Load Alliance
POLA Non-isolated
omax
Output Current
Product Family
Input Voltage
0.8-3.6 Vdc
, C
VOLTAGE
OUTPUT
Compatible
The ultra-wide output voltage trim range offers major advantages to users who
select the PTH05050. It is no longer necessary to purchase a variety of
modules in order to cover different output voltages. The output voltage can be
trimmed in a range of 0.8 Vdc to 3.6 Vdc. When the PTH05050 converter
leaves the factory the output has been adjusted to the default voltage of 0.8 V.
PTH05050
out
5 V i n s i n g l e o u t p u t
Always 0
05 = 5 V
05 = 6 A
= 100 µF.
O O u u t t p p u u t t V V o o l l t t a a g g e e A A d d j j u u s s t t m m e e n n t t o o f f t t h h e e P P T T H H 0 0 5 5 0 0 5 5 0 0 S S e e r r i i e e s s
CURRENT
OUTPUT
P T H 0 5 0 5 0 W A S T
(MIN.)
0 A
CURRENT
OUTPUT
(MAX.)
6 A
EFFICIENCY
(MAX.)
95%
OUTPUT VOLTAGE
EFFICIENCY TABLE (I
Vo = 1.0 V
Vo = 1.2 V
Vo = 1.5 V
Vo = 1.8 V
Vo = 2.0 V
Vo = 2.5 V
Vo = 3.3 V
Packaging Options
No Suffix = Trays
T = Tape and Reel
Mounting Option
D = Horizontal Through-Hole (Matte Sn)
H = Horizontal Through-Hole (Sn/Pb)
S = Surface-Mount (63/37 Sn/Pb
Z = Surface-Mount (96.5/3.0/0.5 Sn/Ag/Cu
Pin Option
A = Through-Hole Std. Pin Length (0.140”)
A = Surface-Mount Tin/Lead Solder Ball
Output Voltage Code
W = Wide
±10 mV
LINE
pin solder material)
pin solder material)
REGULATION
File Name: pth05050.pdf Rev (06): 16 Dec 2005
±12 mV
LOAD
(9)
(8)
EFFICIENCY
O
NEW Product
= 4 A)
85%
87%
89%
90%
91%
93%
95%
NUMBER
PTH05050
MODEL
(9,10)
2