EA-IF-E2 EA ELEKTRO-AUTOMATIK, EA-IF-E2 Datasheet - Page 57

no-image

EA-IF-E2

Manufacturer Part Number
EA-IF-E2
Description
INTERFACE ETHERNET (EA-PSI/BCI800R)
Manufacturer
EA ELEKTRO-AUTOMATIK
Datasheet

Specifications of EA-IF-E2

Svhc
No SVHC (18-Jun-2010)
Accessory Type
Interface Card
Applications
Engineering Laboratory And Complex Industrial Application
Approval Bodies
CE / EN
Rohs Compliant
Yes
For Use With
EA Elektro-Automatik PSU
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
1 Time between occurance of an event, that has to be signalised to an
About the interface cards
© 009, Elektro-Automatik GmbH & Co. KG
IF- G1 (GPIB)
Terminals
Bus standard
Cable length (GPIB)
Cable type (GPIB)
IF-E1 / IF-E2 (Ethernet)
Terminals
Cable type (Ethernet)
Protocols
Used ports (Ethernet)
Network connection
Transmission speed Ethernet
Transmission speed USB
Input current
Response time
output, and the moment it is signalised.
if set to Low Range and Default Level = L
if set to Low Range and Default Level = H
if set to High Range and Default Level = L
if set to High Range and Default Level = H
U
U
U
U
U
U
U
U
U
U
U
U
in
in
in
in
in
in
in
in
in
in
in
in
= 0V
= 1V
= 4V
= 0V
= 1V
= 4V
= 0V
= 1V
= 4V
= 0V
= 1V
= 4V
1)
4pole Centronics socket (female)
Twisted pair, patch cable,
m per device, 0m total
1x RJ45 (LAN / WAN)
Standard GPIB cable
80, 111, 00, 65
1x USB, type A
Cat 3 or higher
IEEE 488.1/
VXI11, HTTP
57600 Baud
10/100 MBit
100 kBaud
+.6mA
+.mA
+1.6mA
+3.5mA
+0.7mA
+4.5mA
< 10ms
-1.5mA
-1.5mA
+5mA
+6mA
0mA
0mA
- never equip two cards of the same type
- the cards IF-R1 and IF-U1 must not be equipped together
- IF-G1 must not be combined with IF-C1 or IF-E1
- IF-E1 must not be combined with IF-C1, IF-G1, IF-R1 or
3. Installation
3.1 After unpacking
After unpacking, check the pluggable interface card(s) for
signs of physical damage. If any damage can be found do
not use and insert the card into any device!
3.2 Inserting a card
The card(s) must only be inserted while the unit is completely
switched off. The unit does not have to be opened. Remove
the screws from the slot cover or from an already equipped
card and remove the cover/card. Insert the new card with
caution until the card plate touches the rear side of the unit.
If there is space between the rear side and the card pla-
te, do not tighten the screws, because the card is not
placed correctly! The wiring between the PC and/or other
units has also be done before the unit is switched on again.
The card(s) will be automatically detected by the device after
powering it on and can now be configured.
Note about the IF-A1: before equipping the card, you should
set the jumpers correctly. Refer to „4.4.1 Configuring the IF-
A1“, subsection „Digital inputs“.
Note: in case the card is not recognized after switching the
unit on, it might be necessary to update the firmware of your
device. Please contact your dealer for further information.
Caution! There are components on the card which are
sensitive for ESD. You must follow the general ESD provi-
sions when handling and installing a card.
3.3 Combining interface cards
At models with more than one card slot following restrictions
apply:
4. Details about the cards
The interface cards are designed to be used in various type of
device series. Depending on the typical features of a certain
device type, like for example an electronic load, the resulting
operability will change. This section handles the configuration
and handling of the cards by example of the PSI 9000 series.
But there are specific characteristics at other device series
which are explained farther below.
Information about the handling and navigation in the menus
and parameter pages of the various device types is available
the corresponding user manuals.
IF-U1
EN
57

Related parts for EA-IF-E2