EA-IF-E2

Manufacturer Part NumberEA-IF-E2
DescriptionINTERFACE ETHERNET (EA-PSI/BCI800R)
ManufacturerEA ELEKTRO-AUTOMATIK
EA-IF-E2 datasheet
 


Specifications of EA-IF-E2

SvhcNo SVHC (18-Jun-2010)Accessory TypeInterface Card
ApplicationsEngineering Laboratory And Complex Industrial ApplicationApproval BodiesCE / EN
Rohs CompliantYesFor Use WithEA Elektro-Automatik PSU
Lead Free Status / RoHS StatusLead free / RoHS Compliant  
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
Page 51
52
Page 52
53
Page 53
54
Page 54
55
Page 55
56
Page 56
57
Page 57
58
Page 58
59
Page 59
60
Page 60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
Page 57/102

Download datasheet (2Mb)Embed
PrevNext
About the interface cards
Input current
if set to Low Range and Default Level = L
U
= 0V
in
U
= 1V
in
U
= 4V
in
if set to Low Range and Default Level = H
U
= 0V
in
U
= 1V
in
U
= 4V
in
if set to High Range and Default Level = L
U
= 0V
in
U
= 1V
in
U
= 4V
in
if set to High Range and Default Level = H
U
= 0V
in
U
= 1V
in
U
= 4V
in
Response time
1)
IF- G1 (GPIB)
Terminals
4pole Centronics socket (female)
Bus standard
Cable length (GPIB)
m per device, 0m total
Cable type (GPIB)
IF-E1 / IF-E2 (Ethernet)
Terminals
Cable type (Ethernet)
Twisted pair, patch cable,
Protocols
Used ports (Ethernet)
Network connection
Transmission speed Ethernet
Transmission speed USB
1 Time between occurance of an event, that has to be signalised to an
output, and the moment it is signalised.
© 009, Elektro-Automatik GmbH & Co. KG
3. Installation
0mA
3.1 After unpacking
+.6mA
After unpacking, check the pluggable interface card(s) for
+5mA
signs of physical damage. If any damage can be found do
not use and insert the card into any device!
-1.5mA
+.mA
3.2 Inserting a card
+6mA
The card(s) must only be inserted while the unit is completely
switched off. The unit does not have to be opened. Remove
0mA
the screws from the slot cover or from an already equipped
+1.6mA
card and remove the cover/card. Insert the new card with
+3.5mA
caution until the card plate touches the rear side of the unit.
If there is space between the rear side and the card pla-
-1.5mA
te, do not tighten the screws, because the card is not
+0.7mA
placed correctly! The wiring between the PC and/or other
+4.5mA
units has also be done before the unit is switched on again.
< 10ms
The card(s) will be automatically detected by the device after
powering it on and can now be configured.
Note about the IF-A1: before equipping the card, you should
set the jumpers correctly. Refer to „4.4.1 Configuring the IF-
A1“, subsection „Digital inputs“.
IEEE 488.1/
Note: in case the card is not recognized after switching the
unit on, it might be necessary to update the firmware of your
device. Please contact your dealer for further information.
Standard GPIB cable
Caution! There are components on the card which are
sensitive for ESD. You must follow the general ESD provi-
sions when handling and installing a card.
1x RJ45 (LAN / WAN)
3.3 Combining interface cards
1x USB, type A
At models with more than one card slot following restrictions
apply:
Cat 3 or higher
- never equip two cards of the same type
VXI11, HTTP
- the cards IF-R1 and IF-U1 must not be equipped together
80, 111, 00, 65
- IF-G1 must not be combined with IF-C1 or IF-E1
10/100 MBit
- IF-E1 must not be combined with IF-C1, IF-G1, IF-R1 or
100 kBaud
IF-U1
57600 Baud
4. Details about the cards
The interface cards are designed to be used in various type of
device series. Depending on the typical features of a certain
device type, like for example an electronic load, the resulting
operability will change. This section handles the configuration
and handling of the cards by example of the PSI 9000 series.
But there are specific characteristics at other device series
which are explained farther below.
Information about the handling and navigation in the menus
and parameter pages of the various device types is available
the corresponding user manuals.
EN
57