EA-IF-E2

Manufacturer Part NumberEA-IF-E2
DescriptionINTERFACE ETHERNET (EA-PSI/BCI800R)
ManufacturerEA ELEKTRO-AUTOMATIK
EA-IF-E2 datasheet
 


Specifications of EA-IF-E2

SvhcNo SVHC (18-Jun-2010)Accessory TypeInterface Card
ApplicationsEngineering Laboratory And Complex Industrial ApplicationApproval BodiesCE / EN
Rohs CompliantYesFor Use WithEA Elektro-Automatik PSU
Lead Free Status / RoHS StatusLead free / RoHS Compliant  
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
Page 71
72
Page 72
73
Page 73
74
Page 74
75
Page 75
76
Page 76
77
Page 77
78
Page 78
79
Page 79
80
Page 80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
Page 77/102

Download datasheet (2Mb)Embed
PrevNext
About the interface cards
5. Operation in other device series
5.1 Electronic loads EL 3000 / EL 9000
The electronic loads of the series EL3000 and EL9000 sup-
port the following interface cards:
IF-U1, IF-R1, IF-C1, IF-G1
Note about the GPIB card IF-G1: at devices with firmware
version
2.11
or older the card is detected as IF-C1 (CAN
card) and must be configured to following settings:
- CAN Baudrate: 100kBd
- Bus termination: no
- Relocatable ID: 0
Also, in devices with firmware version
card is not correctly supported. We recommend an update.
Please contact your dealer.
At firmware version
3.01
or higher there are no limitations.
The general functionality of the interface cards is the same
if used in a power supply. The amount of features is limited,
but also different.
Please refer to the previous sections for detailed information
about the interface cards.
You can configure the interface cards in the setup menu of
the devices. This is activated by turning the switch Level
Control to position Setup.
EL 3000/9000 Menu example of the CAN card:
Card found: IF-C1
CAN Baudrate: 10kBd
Card found: IF-C1
CAN Relocatable ID: 13
Card found: IF-C1
CAN Bus terminate: yes
EL 3000/9000 Menu example RS3 card:
Card found: IF-R1
RS232 Baudrate: 9600Bd
© 009, Elektro-Automatik GmbH & Co. KG
Depending on which card is equipped (the electronic loads
feature only one card slot) a different selection of parameters
is available. The parameters and their values are identical to
the ones explained in section 4.1 to 4.3, with the exception
that no
Sample point
There are also no settable parameters for the USB and
IEEE cards.
5.2 Series PS 8000 T/ DT / 2U
Access to the device setup via pushbutton Fine (press >s
while output is „off“), for details of settings see user manual of
the device. The GPIB and USB cards are not configured.
5.3 Series PSI 800 R
2.14
or lower, the
The shortened type  cards are used here. Setup and c
configuration are explained in the user manual of the device
and also in section 4 (menu structure and handling of PSI
800 R series is similiar to PSI 9000 series).
EN
can be set at CAN.
77