LXHL-DM01 LUMILEDS, LXHL-DM01 Datasheet
LXHL-DM01
Specifications of LXHL-DM01
Available stocks
Related parts for LXHL-DM01
LXHL-DM01 Summary of contents
Page 1
... LUXEON Emitters give you total design freedom and unmatched bright ness, creating a new world of light. LUXEON Emitters can be purchased in reels for high volume assembly. For more information, consult your local Lumileds representative. For high volume applications, custom LUXEON power light source designs are available upon request, to meet your specific needs. ...
Page 2
Mechanical Dimensions Notes: 1. The anode side of the device is denoted by a hole in the lead frame. Electrical insulation between the case and the board is required—slug of device is not electrically neutral. Do not electrically connect either ...
Page 3
Mechanical Dimensions, Continued Notes: 1. The anode side of the device is denoted by a hole in the lead frame. Electrical insulation between the case and the board is required—slug of device is not electrically neutral. Do not electrically connect ...
Page 4
... Royal Blue product is binned by radiometric power and peak wavelength rather than photometric lumens and dominant wavelength July 2003 Philips Lumileds announced a second generation white batwing product using a new phosphor deposition process resulting in improved color uniformity, LXHL BW02. LUXEON Emitter DS25 (5/07) Table ...
Page 5
... Philips Lumileds maintains a tolerance of ± 0.5nm for dominant wavelength measurements. 2. Royal Blue product is binned by radiometric power and peak wavelength rather than photometric lumens and dominant wavelength. Philips Lumileds maintains a tolerance of ± 2nm for peak wavelength measurements. 3. CCT ±5% tester tolerance. 4. Spectral width at ½ of the peak intensity. ...
Page 6
... Royal Blue Red Red Orange Amber Notes for Table 4: 1. Philips Lumileds maintains a tolerance of ± 0.06V on forward voltage measurements. 2. Dynamic resistance is the inverse of the slope in linear forward voltage model for LEDs. See Figures 3a and 3b. Measured between 25°C ≤ T ≤ 110° 350mA. J LUXEON Emitter DS25 (5/07) Table 4 ...
Page 7
... Proper current derating must be observed to maintain junction temperature below the maximum. For more information, consult the LUXEON Design Guide, available upon request. 2. LEDs are not designed to be driven in reverse bias. Please consult Philips Lumileds' Application Brief AB11 for further information. 3. Measured at leads, during lead soldering and slug attach, body temperature must not exceed 120°C. LUXEON emitters cannot be soldered by general IR or Vapor phase reflow, nor by wave soldering ...
Page 8
... Figure 1b. White Color Spectrum of Typical CCT Part, Integrated Measurement. Applicable for LXHL BW02. 1.0 0.8 0.6 0.4 0.2 0.0 350 Figure 1c. White Color Spectrum of Typical Warm White Part, Integrated Measurement. Applicable for LXHL BW03. LUXEON Emitter DS25 (5/07) Figure 1a. Relative Intensity vs. Wavelength 400 450 500 550 600 ...
Page 9
Light Output Characteristics 150 140 130 120 110 100 200 180 160 140 120 100 LUXEON Emitter DS25 (5/07) Green Pho to metric Cyan Pho to metric Blue Photo metric White Pho to metric Ro ...
Page 10
Forward Current Characteristics, T Note: Driving these high power devices at currents less than the test conditions may produce unpredictable results and may be subject to variation in performance. Pulse width modulation (PWM) is recommended for dimming effects. LUXEON Emitter ...
Page 11
Forward Current Characteristics, T Note: Driving these high power devices at currents less than the test conditions may produce unpredictable results and may be subject to variation in performance. Pulse width modulation (PWM) is recommended for dimming effects. Figure 4a. ...
Page 12
Current Derating Curves 400 350 300 250 200 150 100 Figure 5a. Maximum Forward Current vs. Ambient Temperature. Derating based on T 400 350 300 250 200 150 100 Figure 5b. Maximum Forward Current vs. Ambient Temperature. Derating based on ...
Page 13
... Angular Displacement (Degrees) Figure 6a. Typical Representative Spatial Radiation Pattern for LUXEON Emitter Warm White (LXHL BW03). T ypical Upper Bound T ypicalLower Bound 0 -100 -80 -60 -40 - Angular Displacement (Degrees) Figure 6b. Typical Representative Spatial Radiation Pattern for LUXEON Emitter Green, Cyan, Blue and Royal Blue. ...
Page 14
... LUXEON Emitter Red (LXHL BD03), Red Orange (LXHL BH03) and Amber (LXHL BL03). LUXEON Emitter DS25 (5/07) -80 -60 -40 - Angular Displacement (Degrees) Figure 6d. Typical Representative Spatial Radiation Pattern for LUXEON Emitter Red (LXHL BD01) and Amber (LXHL BL01). ...
Page 15
... Typical Lambertian Representative Spatial Radiation Pattern Note: For more detailed technical information regarding LUXEON radiation patterns, please consult your Philips Lumileds Authorized Distributor or Philips Lumileds sales representative. 100 100 Typical Side Emitting Representative Spatial Radiation Pattern 100 LUXEON Emitter DS25 (5/07) ...
Page 16
... Lifetime for solid state lighting devices (LEDs) is typically defined in terms of lumen maintenance—the percentage of initial light output remaining after a specified period of time. Philips Lumileds projects that LUXEON products will deliver on average 70% lumen maintenance at 50,000 hours of operation. This performance is based on independent test data, Philips Lumileds histor ical data from tests run on similar material systems, and internal LUXEON reliability testing. This projection is based on constant current 350 mA operation with junction temperature maintained at or below 90° ...
Page 17
... Notes: 1. LUXEON emitters should be picked up by the body (not the lens) during placement. The inner diameter of the pick up collet should be greater than or equal to 6.5 mm. Please consult Philips Lumileds Application Brief AB10 on LUXEON Emitter assembly information for further details on assembly methods. 2. Drawings not to scale. ...
Page 18
... Notes: 1. LUXEON emitters should be picked up by the body (not the lens) during placement. The inner diameter of the pick up collet should be greater than or equal to 6.5 mm. Please consult Philips Lumileds Application Brief AB10 on LUXEON Emitter assembly information for further details on assembly methods. 2. Drawings not to scale. ...
Page 19
... LEDs and systems are enabling new applications and markets in the lighting world. ©2007 Philips Lumileds Lighting Company. All rights reserved. Product specifications are subject to change without notice. Luxeon is a registered trademark of the Philips Lumileds Lighting Company in the United States and other countries. Philips Lumileds may make process or ...