LEDWA62X62W BANNER ENGINEERING, LEDWA62X62W Datasheet - Page 2

• Manufacturer Part Number: LEDWA62X62W
• Description: LED Area Light
• Manufacturer: BANNER ENGINEERING

Specifications of LEDWA62X62W

• Led Module Type: Board + LED
• Led Color: White
• Power Module Configuration: Square
• Supply Voltage: 24V
• Forward Current @ Test: 200mA
• Operating Temperature Range: 0°C To +50°C
• No. Of Pins: 3
• Forward Voltage: 24V
• Forward Current If: 200mA

NOTE: Before installing this area light it is recommended that an
Sensing Shiny Surfaces
To eliminate direct reflections without using polarizing filters, angle
the sensor approximately 15° (or more) from perpendicular to a
shiny surface.
LED..A62X62W Series Area Lights
Figure 1. Area light dimensions
SMBVLA62X62S
P/N 121779 rev. B
Banner Engineering Corp., 9714 Tenth Ave. No., Minneapolis, MN 55441 • Phone: [phone] • www.bannerengineering.com • [e-mail]
63.5 mm
(2.50")
62 x 62 Models
ambient light filter be installed behind the lens. The filter
improves image quality by reducing unwanted ambient
light.
14.7 mm
(0.58")
59.2 mm
38.1 mm
25.4 mm
(2.33")
67.3 mm
(1.50")
(2.65")
(1.0")
• Inline bracket
• 14 gauge steel, black zinc-plated
64.2 mm
(2.53")
Clearance for
1/4 - 20 screw (Included)
32 mm
(1.26")
6.4 mm
(0.25")
7.6 mm
(0.30")
Clearance for M6 (1/4 - 20) hardware
(Hardware not included)
8.4 mm
(0.33")
WARRANTY: Banner Engineering Corp. warrants its products to be free from defects for one year.
Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture found
to be defective at the time it is returned to the factory during the warranty period. This warranty does
not cover damage or liability for the improper application of Banner products. This warranty is in lieu
of any other warranty either expressed or implied.
53.3 mm
(2.10")
55.9 mm
(2.2")
Installing the Area Light
Mounting Brackets
1.9 mm
(0.07")
SMBVLA62X62RA
63.5 mm
(2.50")
Polarizing Kit
If it is necessary to mount the camera at a 90° angle to a shiny
surface, the polarizing filter kit provides filters for both the LED area
light and sensor to reduce the negative effects of strong, direct light
reflections. The red filter kit (FLTR) is included with the polarizing
kit. When light colors other than red are used, discard the red filter
in the polarizing kit and use the proper filter listed on page 1. The
polarizing filters reduce the amount of light returned to the sensor.
55.9 mm
4.2 mm
(0.17")
(2.2")
59.2 mm
38.1 mm
38.1 mm
25.4 mm
(2.33")
25.4 mm
67.3 mm
(1.50")
(1.50")
(2.65")
(1.0")
(1.0")
• Right-angle bracket
• 14 gauge steel, black zinc-plated
66.7 mm
(2.63")
Clearance for 1/4 - 20 screw (Included)
21.2 mm
(0.84")
19.1 mm
(0.75")
8.4 mm
(0.33")
Clearance for M6 (1/4 - 20) hardware
(Hardware not included)
53.3 mm
(2.10")
66.7 mm
(2.63")
1/4- 20 PEM Nut
1.9 mm
(0.07")