AMMP-6233-TR2G Avago Technologies US Inc., AMMP-6233-TR2G Datasheet
AMMP-6233-TR2G
Specifications of AMMP-6233-TR2G
Available stocks
Related parts for AMMP-6233-TR2G
AMMP-6233-TR2G Summary of contents
Page 1
... AMMP-6233 GHz GaAs Low Noise Amplifier Data Sheet Description Avago Technologies’ AMMP-6233 is a high gain, low- noise amplifier that operates from 18 GHz to 32 GHz. It has noise figure, over gain and designed easy-to-use drop-in with any surface mount PCB application. Popular applications include microwave ra- dios, 802.16 and satellite VSAT or DBS receivers. The fully integrated microwave circuit eliminated the complex tuning and assembly processes typically required by hybrid (discrete-FET) amplifiers. The surface mount pack- age allows elimination of “ ...
Page 2
... Max channel temperature Tstg Storage temperature Tmax Maximum Assembly Temp Notes: 1. Operation in excess of any of these conditions may result in per- manent damage to this device. The absolute maximum ratings for Vd, Id and Pin were determined at an ambient temperature of 25°C unless noted otherwise. (4,5,6) AMMP-6233 RF Specifications TA= 25°C, Vdd=3.0 V, Idd= 65 mA, Zin=Zo=50 Ω Symbol Parameters and Test Conditions Freq Operational Frequency Gain RF Small Signal Gain NF Noise Figure into 50Ω ...
Page 3
... AMMP-6233 Typical Performance (TA = 25°C, Vdd=3V, Idd=65mA, Zin = Zout = 50 Ω unless noted Frequency (GHz) Figure 1. Gain 0 -5 -10 -15 -20 -25 - Frequency (GHz) Figure 3. Input Return Loss 0 -5 -10 -15 -20 -25 - Frequency (GHz) Figure 5. Output Return Loss 6.0 5.0 4.0 3.0 2.0 1.0 0.0 ...
Page 4
... AMMP-6233 Typical Performance (cont) (TA = 25°C, Vdd=3V, Idd=65mA, Zin = Zout = 50 Ω unless noted Frequency (GHz) Figure 7. Gain over Vdd Frequency (GHz) Figure 9. Gain over Temperature 3.5 4 Vdd (V) Figure 11. Idd over Vdd Note: 1. S-parameters are taken with the Evaluation Board as shown in Figure 14. Effects of board and connector are included in the graphs. Loss of board and connector are de-embeded from Gain data. 2. Noise Figure is measured with a 3-dB pad at the input of the device. Losses are de-embeded from the data shown in Figure 2, 8 and 10. ...
Page 5
... AMMP-6233 Application and Usage Vdd 0.1uF RFin AMMP-6233 Figure 13. Application of AMMP-6233 Figure 14. Evaluation / Test Board (Available to qualified customer re- quests) In Figure 15. Simplified LNA Schematic Biasing and Operation The AMMP-6233 is normally biased with a positive drain supply connected to the VDD pin through a 0.1uF bypass capacitor as shown in Figure 13. The recommended drain supply voltage is 3V important to have 0.1uF bypass capacitor, and the capacitor should be placed as close to the component as possible ...
Page 6
... Figure 16b. PCB Stencil Layouts NOTES: DIMENSIONS ARE IN INCHES [MILIMETERS] ALL GROUNDS MUST BE SOLDERED TO PCB RF Material is Rogers RO4350, 0.010” thick The AMMP Packaged Devices are compatible with high volume surface mount PCB assembly processes. The PCB material and mounting pattern, as defined in the data sheet, optimizes RF performance and is strongly recommended. An electronic drawing of the land pat- tern is available upon request from Avago Sales & Ap- plication Engineering ...
Page 7
Manual Assembly • Follow ESD precautions while handling packages. • Handling should be along the edges with tweezers. • Recommended attachment is conductive solder paste. Please see recommended solder reflow profile. Neither Conductive epoxy or hand soldering is recom- mended. • Apply solder paste using a stencil printer or dot place- ment volume of solder paste will be dependent on PCB and component layout and should be controlled to ensure consistent mechanical and electrical perfor- mance. • Follow solder paste and vendor’s recommendations when developing a solder reflow profile. A standard profile will have a steady ramp up from room tem- perature to the pre-heat temp. to avoid damage due to thermal shock. ...
Page 8
... AMMP-6233-BLKG 10 AMMP-6233-TR1G 100 AMMP-6233-TR2G 500 Note performance degradation is seen due to esd upto 50v hbm and 200v mm. the dc char- acteristics in general show increased leakage at lower esd discharge voltages. the user is reminded that this device is esd sensitive and needs to be handled with all necessary esd protocols. ...