Optocoupler(5MBd),T/R+IEC+LF

 

HCPL-2211-560E

Manufacturer Part NumberHCPL-2211-560E
DescriptionOptocoupler(5MBd),T/R+IEC+LF
ManufacturerAvago Technologies US Inc.
HCPL-2211-560E datasheet
 

Specifications of HCPL-2211-560E

Voltage - Isolation3750VrmsNumber Of Channels1, Unidirectional
Current - Output / Channel25mAData Rate5MBd
Propagation Delay High - Low @ If150ns @ 3mACurrent - Dc Forward (if)10mA
Input TypeDCOutput TypePush-Pull, Totem-Pole
Mounting TypeSurface Mount, Gull WingPackage / Case8-SMD Gull Wing
Number Of Elements1Forward Voltage1.7V
Forward Current10mAOutput Current25mA
Isolation Voltage3750VrmsPackage TypePDIP SMD
Operating Temp Range-40C to 85CPower Dissipation210mW
Propagation Delay Time300nsPin Count8
MountingSurface MountReverse Breakdown Voltage5V
Operating Temperature ClassificationIndustrialLead Free Status / RoHS StatusLead free / RoHS Compliant
1
Page 1
2
Page 2
3
Page 3
4
Page 4
5
Page 5
6
Page 6
7
Page 7
8
Page 8
9
Page 9
10
Page 10
11
12
13
14
15
16
17
18
Page 1/18

Download datasheet (368Kb)Embed
Next
HCPL-2201, HCPL-2202, HCPL-2211,HCPL-2212,
HCPL-2231, HCPL-2232, HCPL-0201, HCPL-0211,
HCNW2201, HCNW2211
Very High CMR, Wide V
Logic Gate Optocouplers
CC
Data Sheet
Lead (Pb) Free
RoHS 6 fully
compliant
RoHS 6 fully compliant options available;
-xxxE denotes a lead-free product
Description
The HCPL-22XX, HCPL-02XX, and HCNW22XX are optical-
ly-coupled logic gates. The HCPL-22XX, and HCPL-02XX
contain a GaAsP LED while the HCNW22XX contains an
AlGaAs LED. The detectors have totem pole output stag-
es and optical receiver input stages with built-in Schmitt
triggers to provide logic-compatible waveforms, eliminat-
ing the need for additional waveshaping.
A superior internal shield on the HCPL-2211/12, HCPL-
0211, HCPL-2232 and HCNW2211 guarantees common
mode transient immunity of 10 kV/µs at a common
mode voltage of 1000 volts.
Functional Diagram
HCPL-2201/11
HCPL-0201/11
HCNW2201/11
NC
1
8
V
CC
V
2
7
ANODE
O
NC
3
6
CATHODE
CATHODE
4
5
NC
GND
SHIELD
HCPL-2231/32
8
ANODE 1
1
V
CC
V
2
7
CATHODE 1
O1
6
V
CATHODE 2
3
O2
4
5
ANODE 2
GND
SHIELD
A 0.1 µF bypass capacitor must be connected between pins 5 and 8.
CAUTION: It is advised that normal static precautions be taken in handling and assembly
of this component to prevent damage and/or degradation which may be induced by ESD.
HCPL-2201 Functional Diagram
Features
• 10 kV/µs minimum Common Mode Rejection
(CMR) at V
HCNW2211)
• Wide operating V
• 300 ns propagation delay guaranteed over the full
temperature range
• 5 Mbd typical signal rate
• Low input current (1.6 mA to 1.8 mA)
• Hysteresis
• Totem pole output (no pullup resistor required)
• Available in 8-Pin DIP, SOIC-8, widebody packages
• Guaranteed performance from -40°C to 85°C
• Safety approval
– UL recognized -3750 V rms for 1 minute (5000 V
HCPL-2202/12
NC
1
8
V
CC
– CSAapproved
2
7
NC
ANODE
– IEC/EN/DIN EN 60747-5-2 approved with V
3
6
V
O
4
5
NC
GND
SHIELD
• MIL-PRF-38534 hermetic version available
(HCPL-52XX/62XX)
TRUTH TABLE
Applications
(POSITIVE LOGIC)
LED
V
O
• Isolation of high speed logic systems
ON
HIGH
OFF
LOW
• Computer-peripheral interfaces
• Microprocessor system interfaces
• Ground loop elimination
• Pulse transformer replacement
• High speed line receiver
• Power control systems
= 1000 V (HCPL-2211/2212/0211/2232,
CM
range: 4.5 to 20 Volts
CC
rms for 1 minute for HCNW22XX) per UL1577
630 V
(HCPL-2211/2212 Option 060 only) and
peak
V
= 1414 V
(HCNW22XX only)
IORM
peak
=
IORM

HCPL-2211-560E Summary of contents

  • Page 1

    ... Schmitt triggers to provide logic-compatible waveforms, eliminat- ing the need for additional waveshaping. A superior internal shield on the HCPL-2211/12, HCPL- 0211, HCPL-2232 and HCNW2211 guarantees common mode transient immunity of 10 kV/µ common mode voltage of 1000 volts. ...

  • Page 2

    ... Notes: 1. HCPL-2200/2219 devices include output enable/disable function. 2. Technical data for the HCPL-2200/2219, HCPL-52XX and HCPL-62XX are on separate Avago publications. 3. Minimum CMR of 10 kV/µs with V = 1000 V can be achieved with input current Schematic – ...

  • Page 3

    ... To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. Example 1: HCPL-2202-560E to order product of 300mil DIP Gull Wing Surface Mount package in Tape and Reel packaging with IEC/EN/DIN EN 60747-5-2 Safety Approval in RoHS compliant. Example 2: HCPL-2202 to order product of 300mil DIP package in tube packaging and non RoHS compliant ...

  • Page 4

    ... TYPE NUMBER A XXXXZ YYWW 1.19 (0.047) MAX. 3.56 ± 0.13 (0.140 ± 0.005) 1.080 ± 0.320 (0.043 ± 0.013) 8-Pin DIP Package with Gull Wing Surface Mount Option 300 (HCPL-2201/02/11/12/31/32) 9.65 ± 0.25 (0.380 ± 0.010 1.19 (0.047) MAX. 1.080 ± 0.320 (0.043 ± ...

  • Page 5

    ... Small-Outline SO-8 Package (HCPL-0201/11 XXX 3.937 ± 0.127 YWW (0.155 ± 0.005 PIN ONE 0.406 ± 0.076 (0.016 ± 0.003) * 5.080 ± 0.127 (0.200 ± 0.005) 3.175 ± 0.127 (0.125 ± 0.005) * TOTAL PACKAGE LENGTH (INCLUSIVE OF MOLD FLASH) 5.207 ± 0.254 (0.205 ± 0.010) DIMENSIONS IN MILLIMETERS (INCHES) ...

  • Page 6

    Widebody DIP Package with Gull Wing Surface Mount Option 300 (HCNW2201/11) 11.23 ± 0.15 (0.442 ± 0.006 1.55 (0.061) MAX. 1.80 ± 0.15 (0.071 ± 0.006) 2.54 (0.100) BSC DIMENSIONS IN ...

  • Page 7

    ... PREHEAT 60 to 180 SEC °C to PEAK TIME Regulatory Information The HCPL-22XX/02XX and HCNW22XX have been approved by the following organizations: UL Recognized under UL 1577, Component Recognition Program, File E55361. CSA Approved under CSA Component Acceptance Notice #5, File CA 88324. Insulation and Safety Related Specifications ...

  • Page 8

    ... IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics (HCPL-2211/2212 Option 060 ONLY) Description Installation classification per DIN VDE 0110/1.89, Table 1 for rated mains voltage ≤300 V rms for rated mains voltage ≤450 V rms Climatic Classification Pollution Degree (DIN VDE 0110/1.89) Maximum Working Insulation Voltage Input to Output Test Voltage, Method ...

  • Page 9

    IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics (HCNW22XX ONLY) Description Installation classification per DIN VDE 0110/1.89, Table 1 for rated mains voltage ≤600 V rms for rated mains voltage ≤1000 V rms Climatic Classification Pollution Degree (DIN VDE 0110/1.89) Maximum Working ...

  • Page 10

    ... Symbol F(AVG) I F(TRAN) HCNW22XX V R HCNW22XX HCPL-223X P O 260°C for 10 sec., 1.6 mm below seating plane HCNW22XX 260°C for 10 sec seating plane See Package Outline Drawings section Symbol F(ON) HCPL-223X V F(OFF Min. Max. Units Note -55 125 °C -40 85 ° 1 -0.5 20 ...

  • Page 11

    ... Logic Low Short Circuit Output Current Logic High Short Circuit Output Current Input Forward Voltage HCNW22XX Input Reverse Breakdown Voltage HCNW22XX Input Diode Temperature Coefficient HCNW22XX Input Capacitance HCNW22XX *For HCPL-223X, 1.8 mA ≤ I ≤ 5 mA. F(ON) **Typical 2 ≤ ≤ V F(ON) F(OFF) Sym. Min. ...

  • Page 12

    ... HCPL-2232 HCNW2211 Logic Low |CM | HCPL-2201/02 L Common Mode HCPL-0201 Transient HCPL-2231 Immunity HCNW2201 HCPL-2211/12 HCPL-0211 HCPL-2232 HCNW2211 *For HCPL-223X, 1.8 mA ≤ I ≤ 5 mA. F(ON) †I = 1.8 mA for HCPL-2231. F ‡I = 1.8 mA for HCPL-2232 ≤ ≤ F(ON) F(OFF unless otherwise specified. F(ON) Sym. ...

  • Page 13

    ... This test is performed before the 100% production test for partial discharge (Method b) shown in the IEC/ detection current limit, I I-O EN/DIN EN 60747-5-2 Insulation Characteristics Table. 12. For HCPL-2231/32 only. Measured between pins 1 and 2, shorted together, and pins 3 and 4, shorted together. 13 Min. Typ. ...

  • Page 14

    ... Figure 2. Typical logic high output current vs. temperature. HCPL-2201 fig 2 HCNW22XX 1000 100 – 1.0 0.1 0.01 0.001 1.1 1.2 1.3 1.4 V – FORWARD VOLTAGE – HCPL-2201 fig 4b PULSE GEN 100 kHz OUTPUT DUTY MONITORING NODE 5 V 619 Ω INPUT MONITORING NODE ...

  • Page 15

    ... SWITCH OUTPUT V SWITCH (MAX.)* O V (MAX.)* SEE NOTE SEE NOTE 1.8 mA FOR HCPL-2231/32 DEVICES 1.8 mA FOR HCPL-2231/32 DEVICES. F HCPL-2201 fig 10c HCPL-2201 fig 10c ° 100 – SUPPLY VOLTAGE – Figure 7. Maximum output power per channel vs. supply voltage. HCPL-2201 fig 7 ...

  • Page 16

    ... HCPL-2201 fig 11b HCNW22XX 1000 P (mW) S 900 I (mA) S 800 700 600 500 400 300 200 100 100 125 T – CASE TEMPERATURE – °C S HCPL-2201 fig 12b HCPL-2201/11 HCPL-02XX HCNW22XX V CC2 8 DATA OUTPUT LSTTL LOADS TTL LOADS 2 HCPL-2201 fig 13a 80 100 150 175 (+5 V) ...

  • Page 17

    ... GND 4 5 from the LED (+5 V) CC2 DATA OUTPUT LSTTL LOADS OR 4 TTL LOADS HCPL-2201/11 V (+5 V) CC1 1.1 kΩ 1 DATA 2 INPUT D1 TTL or 3 LSTTL 4 D1 (1N4150) REQUIRED FOR ACTIVE PULL-UP DRIVER. Figure 15. Alternative LED drive circuit. HCPL-2201 fig 15 HCPL-02XX HCNW22XX GND 5 ...

  • Page 18

    For product information and a complete list of distributors, please go to our website: Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © 2005-2010 ...